Rexroth coupling male and female hubs 3842218920, Shanghai Weimi Electrical Equipment Co., Ltd. main product, sales hotline: 13524123009; contact person: Lei Qing; real product photos, original factory packaging, affordable prices; warmly welcome both new and old customers to inquire and purchase! 4
Rexroth REXROTH couplings male and female hubs
3842218920
Clutch 30x30X50 SW17
LINCOLN REXROTH Assembly Components: Support Profiles, Connecting Elements, Sliders, Guides, Mounting Boxes, Material Conveying Racks, Workpiece Trays, Conveyors, Conveying Profiles, Bending Sections, Leg Kits, Separators, Stop Blocks, Communication Modules, Antennas and Cables, Assembly Kits.
Löscher REXROTH Mobile Data Carrier MDT...H (13.56 MHz)
MDT with FRAM memory
Data Storage Module MDT1/2K-H
3842410104
The mobile data carrier is compatible with the ISO 15693 standard (13.56 MHz) and operates without a battery, working in tandem with FRAM memory. It offers various housing models, allowing for multiple installation positions on the workpiece tray or direct installation onto the product to be identified. The data carrier can be read from multiple sides, including dynamic reading during passage.
MDT with FRAM memory
Memory Capacity: 2000 bytes of user memory
Additional 64-bit: One serial number
Write-Read Loop: 1010
Mobile Data Carrier MDT...L, suitable for 125 kHz
Portable Data Carrier MDT...L, suitable for 13.56 MHz
Flat Antenna A...F, suitable for 125 kHz or 13.56 MHz
Circular Antenna A...R, suitable for 125 kHz or 13.56 MHz
Communication Module C-..., compatible with PROFIBUS or Ethernet
Control System
Portable Data Carrier 1/2K-H
Frequency: 13.56 MHz
Standard Compliance: ISO 15693
Memory Capacity: 2000 Bytes
Data Access: 8-byte Blocks
Memory Type: FRAM
Write loop quantity ≥ 10 billion
Read Loop Count - Unrestricted
Transmission Distance - Static 35 mm
Transmission Distance - Dynamic 30 mm
Operating temperature during operation: -25 ... +85 °C
Shell Material: PA 66
Protection Type IP68
Rexroth VE 2/S Brake clutch
Pneumatic stopper
For operating reversible conveying sections
Distributor VE 2/S
3842515844
Do not apply pressure to the VE 2/S when the pallet reverses.
Stop one or more stack of workpiece trays at a predetermined stop surface for workpiece trays. The VE 2/S can only stop trays coming from one direction. After pressure is released, the stopper closes through a spring, simultaneously stopping the workpiece tray. Two VE 2/S stoppers are required to stop trays from both directions, as reverse-running trays cannot apply pressure to the stopper. Installed inside the conveyor roller, directly mounted on the conveying section.
Total Gross Weight of Workpiece Pallet: 140kg
Operating Temperature T 0 ... +60℃
Material Specifications
Shell: PA 6
Bolt Head Cam: PA 66
Required compressed air interface P 4 ... 6bar
Pneumatic insertion with φ 4mm fit
The safety lock bolt can be actively (pneumatically) opened for safe transfer from both directions.
Scope of Supply
Including fastening materials for installation on ST 2/... conveying sections
Rexroth spring puller
The spring puller is designed to provide tools, such as screws, in an ergonomically friendly manner to reduce uneven high stress on workers.
The spring-powered puller features a retractable cable, designed for ergonomically delivering pneumatic tools, such as pneumatic screws, to reduce uneven high stress on workers.
Spring Puller, 0.4-1.0 KG
Weight: 0.6 kg
Retractable Cable 1600mm
Order Number: 3842520053
3842520054
Load-bearing capacity and adjustable cable length
Use hoists and pulleys, or sliding hoists for assembly at the work station.
Retractable Cable Spring Puller
Compressed air via air blower
Compressed air fitting for connecting feed tubes and tools: G1/4"
Bosch Rexroth Data Memory
ID 10/D carries information through the workpiece.
Multiple ID 10/D units can be connected to the workpiece tray.
Bosch-Rexroth Braking Stopper
Pneumatic Gate
Reversible operation sections
Do not apply pressure to the VE 2/S when the pallet is moving in reverse.
Stop one or more accumulated workpiece trays at the defined stop surface of the workpiece tray. The VE 2/S can only stop trays coming from one direction. Upon releasing pressure, the stop gate closes with a spring, stopping the workpiece tray. Two VE 2/S stop gates are required to stop trays from both directions, as pressure should not be applied to the stop gates when the trays move in reverse. Installed internally on the track, directly mounted on the conveyor section.
Rexroth REXROTH Separator VE 1
Pneumatic separator. Upon pressure release, the separator closes via spring, simultaneously stopping the workpiece tray.
Tilt Lock; can be opened without wearing down the stop surface of the work tray.
The allowable total load for all workpiece trays in operation: 80 kg (conveyor speed 9 m/min)
The separator is used to stop the workpiece tray. The actuation is executed by pneumatic means. In the unpressurized state, the separator is held in the blocking position by a spring, which is of great significance to production safety.
Stop one or more stacked workpiece trays at the defined workpiece tray stop surface.
Item Number: 3842522400
Large conveying section load during stacking operation: 80kg
Cleanroom Class ISO 7
Drying Room r.F. <1%
Required compressed air connection: p 4 ... 6 bar
Pneumatic insertion with φ 4mm fit
Rexroth Mounting Bracket 60/60
Bracket 6060 Sets (Standard Type) N10/10 3842523553
Bracket with locating lugs for quick assembly and anti-rotation.
Positioned lugs are easy to remove for assembly on panels or to be fitted at right angles into slots.
Version designLINE, featuring a special silver powder coating (RAL 9006), truly high-quality design
Intermediate component for positioning the bracket in the next large lock pit.
End caps, dust-proof, available in Signal Grey (RAL 7004) and Black ESD (RAL 9005) versions.
Precision profile processing: Not required
Recommended Accessories
10 mm keyed groove intermediate component
Bracket end cover 60/60, Signal gray
Bracket end cover 60/60, black
Rexroth Support Bracket 45/45
Bracket with positioning lugs for quick assembly and anti-rotation
Positioned lugs are easy to remove for assembly on panels or to fit into slots at right angles.
Version designLINE, featuring a special silver powder paint (RAL 9006), true high-quality design
Offset slider for offset positioning on 45/45 brackets
End caps, dust-proof, available in Signal Grey (RAL 7004) and Black ESD (RAL 9005) versions.
Recommended Accessories
Slider, Offset
Bracket end cap 45/45, signal gray
Bracket end cover 45/45, black
Bracket 45x45 Kit (Standard Type) - Kit includes fasteners 3842523561
Bosch-Rexroth Angle Support Plate 6060 sets of 10/10
3842523553
Bracket with centering boss for quick assembly and to prevent rotation
The centering lugs are easily detachable for assembly on the board or perpendicular to the slots.
Version with special silver paint (RAL 9006) design line, offering especially high-quality design
Intermediate component for positioning the bracket in the next large slot
Dust cover, available in signal gray (RAL 7004) and black ESD (RAL 9005)
Surface Treatment of Profiles: Not Required
REXROTH bracket 45/45
3842523561
Bracket with centering boss for quick assembly and rotation prevention
The centering lugs are easily detachable for assembly on the board or at a right angle to the slots.
Version with special silver paint (RAL 9006) design line, offering high-quality design
Slider offset for eccentric positioning on 45/45 bracket
Dust caps available in signal gray (RAL 7004) and black ESD (RAL 9005)
Rexroth Mounting Bracket 45/90
3842523570
Bracket with centering lugs for quick assembly and to prevent rotation
The centering lugs are easily broken off for assembly on the board or at right angles to the slots.
Version with special silver paint (RAL 9006) design line, offering superior quality design
Dust cap, available in signal gray (RAL 7004) and black ESD (RAL 9005)
Surface Treatment of Profiles: Not Required
Bosch-Rexroth Reinforced Frame Module
3842525998
Self-assembly trays for workpieces with dimensions of 400 x 400 mm and above. Required for workpiece trays with a total weight mW > 50 kg and conveying speed vN > 12 m/min.
400mm Corner Module
320mm Frame Expansion Module
By combining standard modules, various sizes of workpiece pallets can be achieved.
Material:
Corner/Extension Module with PA (Polyamide) Wear Plate
Or
– Corner/Extension Module (PA) with Wear-Resistant Pad of PE (= Polyethylene)
Can be combined with WT 2 carrier board
Strengthened frame modules are required for self-assembly of workpiece trays measuring 400 x 400 mm. Necessary when the total weight of the workpiece tray exceeds 50 kg or the conveyor speed vN is greater than 12 m/min.
The PA basic solution is suitable for belt/pulley and flat-top chain conveyors.
Conveyor systems with double chain and accumulating roller chains require frame modules equipped with PE wear-resistant pads on the medium.
Bosch-Rexroth Standard Frame Modules
3842526762
Corner modules with standard lengths ranging from 160 to 400 mm
320mm Frame Expansion Module
Material:
- Wear-resistant pads with PA (nylon)
Corner/Extension Module (PA) with wear-resistant pad of PE (= polyethylene)
For total weight mW > 50 kg and conveying speed vN > 12 M/min, reinforced frame modules are required.
Can be combined with WT 2 carrier board
Frame modules are used for the self-assembly of workpiece trays. The PA basic solution is suitable for belt/pulley and flat-top chain conveyance media.
The double chain and accumulated roller chain conveyors require frame modules with PE wear-resistant pads on the medium. PE pads are not suitable for accumulation operations on ESD flat top chains.
Bosch-Rexroth scraper
Used for scraping small parts from conveyance medium
3 kg capacity workpiece tray
Conveying Medium: Belts, Toothed Belts, Flat Top Chains
Can be installed on the right (R) or left (L)
Gouged sections cannot be reversibly operated.
Bosch-Rexroth plates
Used for securing and leveling feet in profiles without a central hole
Used as end connectors or T connectors
Precision profile processing: Tapping threads inside the central hole
Materials
Aluminum Casting Sheets
Fasteners: Steel; Galvanized
Bosch-Rexroth GT 2 Belt
The conveyor belt, used as a medium for conveying, transports workpiece trays to the conveying system. The safety belt is pre-tensioned and bonded during installation to form a continuous safety belt. A safety belt installation toolkit is used for joining, tensioning, and bonding.
Use the following formula to determine the required belt length.
Note: The belt requires a pre-tension coefficient F.
Pound = ((2 x Height + Height + Height) x Foot) + 60
lB = Belt Length
lS = Section Length
Length of medium conveyed at the LAS drive module
Length of medium conveyed at the lUM return device location
F=Pre-stretch coefficient
Pre-tension coefficient of the belt F
BS 2 and lS ≤ 4000mm, F = 0.98
BS 2 and lS > 4000 mm, F = 0.975
Equation: AS 2/B-250, F=0.965
Conveyor belt length for conveying medium
LUM = 660 mm
LAS = 660 mm
Belt Expansion
Where lS ≤ 4000 mm = 2%
Where lS > 4000 mm = 2.5%
AS 2/B-250 = 3.5%
Bosch-Rexroth WI 2 Joystick
For regional monitoring
For workpiece tray identification
Stop device for lateral conveying of workpiece trays
Suitable for installation on ST 2/... sections or ST 2/...H sections with a web width of 45 mm or 50 mm respectively
Suitable for use in the EPA
A basic swing arm component for workpiece tray length ≤ 480mm
Two basic swing arm components for workpiece tray length ≥ 640mm
Joysticks are used in the following areas:
For regional monitoring
Stop device for lateral conveying of workpiece trays
Used for workpiece tray identification
According to the required function, a WI/M, WI 2/, or similar arm should be equipped with one or two sensors.
Bosch-Rexroth Rotating Elevating Device
HD 2, b160, l, T160 lifting and rotating unit, DW90, h90
3842525849
3842525859
Enhance Rotating Device HD 2
The Z-axis swivel shaft: 90° or 180°. Optionally, the rotation direction of HD 2/90° can be individually driven for each workpiece tray if needed.
The WT lift distance is 40 mm or 90 mm above the transport level. Models with a 40 mm lift mechanism are suitable for rotating workpiece trays directly above the conveyor section. If any components, such as identification and data storage modules, are installed on the side of the workpiece tray, a 90 mm lift version may be required.
Large Allowable Total Mass Inertia: 0.65 kgm²
The HD 2 lifting turntable rotates the workpiece tray to the required position. In a loop system without curves, this device ensures that the workpiece tray maintains the correct orientation at all times, with the front always facing forward. Operations on the HD 2 can be performed without the need for additional force.
Required accessories
Stopper VE 2/...
M12x1 sensor, rated sensing distance SN ≥ 4 mm, non-flush mounting required with a 0.5 mm offset
Rexroth Rake
Excavator
Excavator, right side 3842532679
Excavator, Left Side 3842532680
Used for scraping small parts off the conveying medium
Combined with workpiece trays of not less than 3 kg in weight.
Conveying Medium: Belt conveyors, toothed belts, and flat-top chains
Can be installed on the right (R) or left (L) side
Reversible operations cannot be achieved on the conveying sections equipped with loaders.
REXROTH Damper DA 1/B
Pneumatic damper
Adjustable damping degree
The allowable load for the workpiece tray is between 0.5 kg and 6 kg (at a conveying speed of 9 m/min).
When the workpiece trolley is moved to the lift and positioning device HP 1/P, the damper DA 1/B is used to cushion impacts on the trolley.
Suitable for mounting on HP 1/P
Item No. 3842535360
Total weight of workpiece trays: 10kg
Cleanroom Class ISO 7
Dry Room r.F. <1%
Weight: 0.5kg
Required compressed air interface p 4 ... 6 bar
Pneumatic insertion with φ 4mm fit
REXROTH conveyor belts
GT 2 Conveyor Belt
GT 2, L250 Conveyor, 3842539479
The conveyor belt, used as a medium for conveying, transports workpiece trays to the conveying system. The belt must be pre-stretched during installation and then bonded to form a continuous conveyor belt. The conveyor belt installation kit is suitable for bonding, stretching, and adhering.
The required conveyor belt length is determined using the following formula.
Description: The conveyor belt requires a pre-stretching coefficient F; please refer to the "Conveyor Belt Pre-stretching Coefficient F" overview.
lB= ((2 x lS+ lAS+ lUM) x F) + 60
lB = Conveyor Belt Length
lS = Length of conveying section
Length of conveying medium for the LAS drive module
Length of conveying medium for lUM rotary unit
F = Pre-stretch coefficient
Pre-tension Factor for Belts F
BS2 and IS ≤ 4000 mm, F = 0.98
BS2 and IS > 4000 mm, F = 0.975
AS 2/B-250, F = 0.965
Belt conveyor medium length
lUM = 660 mm
lAS = 660 mm
Belt Extension
Where IS ≤ 4000 mm = 2%
Where IS > 4000 mm = 2.5%
AS 2/B-250 = 3.5%
Rexroth REXROTH conveying medium belt
The belt is made of nylon, featuring a meshed top with conductivity.
Tension and bond during installation to form a continuous belt
The conveyor belt, used as a medium for transport, carries the workpiece trays into the conveyor system.
Item Number: 3842539480
ESD is
Cleanroom Class ISO 7
Material Data - Polyamide Plastic PA 6.6
Length: 50,000mm
Required Accessories:
Belt installation kit for connecting, tensioning, and bonding purposes.
Glue
Belt GT 1, L1000-50000
Rexroth Plastic Flat Top Chain Main Link
Conveying medium for the self-assembly of transmission units
For use with ST 2/C and ST 2/C-H sections
Delivery unit length reaches 12,000 mm. Multiple flat-top chains connected by the main linkage can achieve a length of l > 12,000 mm.
Nickel-plated Steel Basic Chain Version
Steel chain with PA66 polyamide bearing cover
The workpiece trays in the TS 2plus are paired with the ST 2/C and ST 2/C-H conveying sections.
The required chain length is determined using the following formula.
lC = 2 x lS + lAS + lUM
lC = Flat Top Chain Length
lS = Length of conveying section profile
lAS = Length of the conveying medium in the drive module
lUM = Length of the medium transported in the return device
Length of flat-top chain conveyor medium
lUM 2/C-170 = 310 mm
lUM 2/C-60 = 150 mm
lAS = 625 mm
Part Number 3842551226
Material Data: Basic Chain: Steel; Nickel-plated PAl 66 ESD Flat Chain
Length: 12,000mm
Note:
Plastic flat-top chains are also suitable for EPA use but cannot be used in curves and arcs.
Workpiece trays equipped with PE wear-resistant pads are not recommended for stacking operations as this accelerates wear.
Plastic flat-top chains are not to be used with steel GP sliding profiles.
Recommended Accessories
Additional Closure Link, 3842551234
Flat Top Chain Tool
Main Connecting Rod 3842551234 - Suitable for use on two plastic flat-top chains
Product Range
Plastic flat top chain (length l = 12,000 mm, black), including 1 x main rod
Rexroth Coupling Male and Female Ends 3842218920
