Rexroth coupling male and female hubs 3842218920, Shanghai Weimi Electromechanical Equipment Co., Ltd. Main Product, Sales Hotline: 13524123009; Contact Person: Lei Qing; Product Real Photos, Original Factory Packaging, Reasonable Prices; Warmly welcome new and old customers to inquire and purchase! 4
Rexroth REXROTH couplings male and female ends
3842218920
Clutch 30x30X50 SW17
REXROTH REXROTH Assembly Components: Support Profiles, Connecting Elements, Sliders, Rails, Snap-Fit Containers, Material Conveying Racks, Workpiece Trays, Conveyors, Conveying Profiles, Bending Sections, Leg Kits, Separators, Stop Blocks, Communication Modules, Antennas and Cables, Assembly Kits.
力士乐REXROTH Mobile Data Carrier MDT...H (13.56 MHz)
MDT with FRAM memory
Data Storage Module MDT1/2K-H
3842410104
The mobile data carrier is compatible with the ISO 15693 standard (13.56 MHz) and operates without a battery, working in conjunction with a FRAM memory. Available in various housing models, it can be mounted in multiple positions on the workpiece tray or directly installed on the product to be identified. The data carrier can be read from multiple sides, including dynamic reading while passing through.
MDT with FRAM memory
Memory Capacity: 2000 bytes of user memory
Additional 64-bit: One serial number
Write-Read Loop: 1010
Portable Data Carrier MDT...L, suitable for 125 kHz
Portable Data Carrier MDT...L, suitable for 13.56 MHz
Flat Antenna A...F, suitable for 125 kHz or 13.56 MHz
Circular Antenna A...R, suitable for 125 kHz or 13.56 MHz
Communication Module C-..., suitable for PROFIBUS or Ethernet
Control System
Portable Data Carrier 1/2K-H
Frequency 13.56 MHz
Standard Compliance: ISO 15693
Memory Capacity: 2000 Bytes
Data Access - 8-byte Blocks
Memory Type FRAM
Write quantity loop ≥ 10 billion
Read Loop Quantity - Unrestricted
Transmission Distance - Static 35 mm
Transmission Distance - Dynamic 30 mm
Operating temperature during operation –25 ... +85 °C
Shell Material: PA 66
Protection Type: IP68
Rexroth VE 2/S Brake Chute
Pneumatic Stopper
For operating reversible conveying sections
Distributor VE 2/S
3842515844
When the pallet reverses, do not apply pressure to the VE 2/S.
Stop one or more stacked workpiece trays at the predetermined stop surface for workpiece trays. The VE 2/S can only stop trays coming from one direction. After pressure is released, the stopper closes through the spring, simultaneously stopping the workpiece tray. Two VE 2/S stoppers are required to stop trays from two directions, as reverse-running trays cannot apply pressure to the stopper. Installed inside the roller conveyor, directly mounted on the conveying section.
The total weight of the workpiece pallet is 140kg.
Operating Temperature T 0 ... +60℃
Material Specifications
Shell: PA 6
Bolt Head Cam: PA 66
Required compressed air interface P 4 ... 6bar
Pneumatic insertion with φ 4mm mating
The (pneumatic) actuated safety bolt can be safely transferred from both directions.
Supply Range
Includes fastening materials for installation on ST 2/... conveyor sections
Rexroth REXROTH spring pull-out tool
The spring puller is designed to provide tools, such as screws, in an ergonomic manner to reduce uneven high stress on workers.
This spring-loaded puller features a retractable cable, designed to provide pneumatic tools, such as pneumatic screwdrivers, in an ergonomic manner to reduce uneven high stress on workers.
Spring Puller, 0.4 - 1.0 KG
Weight: 0.6 kg
Retractable Cable 1600mm
Part Number: 3842520053
3842520054
Load-bearing capacity and adjustable cable length
Utilize hoists and pulleys, or sliding hoists for assembly at the work station.
Spring Puller with Retractable Cable
Compressed air provided through a wind rod
Compressed air connector for material tubes and tool connections: G1/4"
Bosch-Rexroth Data Storage Unit
ID 10/D via part-carrying information.
Multiple ID 10/D devices can be connected to the workpiece tray.
Bosch-Rexroth Braking System
Pneumatic gate
Reversible operation sections
Do not apply pressure to the VE 2/S when the pallet reverses.
Stop one or more accumulated workpiece trays at the defined stop surface of the workpiece tray. The VE 2/S can only stop trays coming from one direction. When pressure is released, the stop gate closes with a spring, and the workpiece tray stops. Two VE 2/S stop gates are required to stop trays from both directions, as pressure must not be applied to the stop gates when the trays move in reverse. Installed inside the track, directly mounted on the conveyor section.
Rexroth REXROTH Separator VE 1
Pneumatic separator. Upon pressure release, the separator closes via a spring, simultaneously stopping the workpiece tray.
Tilt stopper; opens without wearing the stop surface of the work tray.
Allowable total load for all workpiece trays in operation: 80 kg (conveyor speed 9 m/min)
The separator is used to stop workpiece trays. The actuation is executed by pneumatic means. In the unpressurized state, the separator is held in the blocking position by a spring, which is of great significance for production safety.
Stop one or more assembled workpiece trays on the defined workpiece tray stop surface.
Part Number 3842522400
Large conveying section load during stacking operation: 80kg
Cleanroom Class ISO 7
Drying Room r.F. <1%
Required compressed air interface p 4 ... 6 bar
Pneumatic insertion with φ 4mm fit
Rexroth REXROTH Bracket 60/60
Bracket 6060 Sets (Standard Type) N10/10 3842523553
Bracket with locating lugs for quick assembly and anti-rotation.
Positioned lugs are easy to remove for assembly on panels or for right-angle mounting into slots.
Version designLINE, featuring a special silver powder coating (RAL 9006), truly high-quality design
Intermediate components for positioning brackets in the next large lock pit.
End caps, dust-proof, available in signal gray (RAL 7004) and black ESD (RAL 9005) versions
Profile precision processing: Not required
Recommended Accessories
10mm lock pit middle component
Bracket End Cap 60/60, Signal Grey
Bracket end cap, 60/60, black
REXROTH bracket 45/45
Bracket with locating lugs for quick assembly and rotation prevention
Positioned lugs are easy to remove for assembly on panels or to fit into slots at right angles.
Version designLINE, featuring special silver powder paint (RAL 9006), truly high-quality design
Offset slider, for offset positioning on 45/45 brackets
End caps, dust-proof, available in signal gray (RAL 7004) and black ESD (RAL 9005) versions.
Recommended Accessories
Slider, Offset
Bracket end cover 45/45, Signal Grey
Bracket end cover 45/45, black
Bracket 45x45 Kit (Standard) - Kit includes fasteners 3842523561
Bosch-Rexroth Angle Support Plate 6060 10/10 sets
3842523553
Bracket with centering lug for quick assembly and rotation prevention
The centering lugs are easily detachable for assembly on the board or at a right angle to the slots.
Version with special silver paint (RAL 9006) design line, offering high-quality design
Intermediate component for positioning the bracket in the next large slot
Dust caps available in signal gray (RAL 7004) and black ESD (RAL 9005).
Surface Treatment for Profiles: Not Required
REXROTH bracket 45/45
3842523561
Bracket with centering lug for quick assembly and rotation prevention
The locating bosses are easily detachable for assembly on the board or perpendicular to the slots.
Version with special silver paint (RAL 9006) design line, offering high-quality design
Slider offset for eccentric positioning on 45/45 bracket
Dust cover, available in signal gray (RAL 7004) and black ESD (RAL 9005)
Rexroth Mounting Bracket 45/90
3842523570
Bracket with centering lug for quick assembly and to prevent rotation
The centering lugs are easily detachable for assembly on the board or perpendicular to the slots.
Version with a special silver paint (RAL 9006) design line, offering particularly high-quality design
Dust cap, available in signal gray (RAL 7004) and black ESD (RAL 9005)
Surface Treatment of Profiles: Not Required
Bosch-Rexroth Reinforced Frame Module
3842525998
Self-assembly trays for workpieces with dimensions of 400 x 400 mm and above. Required for workpiece trays with a total weight mW > 50 kg and conveying speed vN > 12 m/min.
400mm corner module
320mm Frame Expansion Module
By combining standard modules, various sizes of workpiece pallets can be achieved.
Material:
Corner/Extension Module with PA (Polyamide) Wear Pad
Or
Corner/Extension Module (PA) with wear-resistant pad made of PE (=polyethylene)
Can be combined with WT 2 carrier plate
Strengthened frame modules are required for self-assembly of workpiece trays measuring 400 x 400 mm. Necessary when the total weight of the workpiece tray exceeds 50 kg or when the conveyor speed vN is greater than 12 m/min.
The PA basic solution is suitable for belt/pulley and flat-top chain conveyors.
Frame modules with PE wear-resistant pads are required on the medium of double chain and accumulator roller conveyor.
Bosch-Rexroth Standard Frame Module
3842526762
Corner modules with standard edge lengths of 160 to 400 mm
320mm Frame Expansion Module
Material:
- Wear-resistant pads with PA (=polyamide)
- Corner/Extension Module (PA) with Wear-Resistant Pad of PE (= Polyethylene)
For total weight mW > 50 kg and conveying speed vN > 12 M/min, reinforced frame modules are required.
Can be combined with WT 2 carrier plate
Frame modules are used for the self-assembly of workpiece trays. The PA basic solution is suitable for belt/pulley and flat-top chain conveyance mediums.
The double chain and cumulative roller conveyor requires frame modules with PE wear-resistant pads on the medium. PE pads are not suitable for accumulation operations on ESD flat top chains.
Bosch-Rexroth scraper
Used for scraping small parts from conveyance medium
3 kg lightweight workpiece tray
Conveying Medium: Belts, Ribbed Belts, Flat Top Chains
Installable on the right (R) or left (L)
The scraped section cannot be subjected to reversible operations.
Bosch-Rexroth plates
Used for securing and leveling feet in profiles without a central hole
Used as end connectors or T connectors
精密型材加工: Tapping threads within the central hole
Materials
Aluminum Extrusion Plates
Fasteners: Steel; Zinc-plated
Bosch-Rexroth GT 2 Belt
The conveyor belt, used as a medium for transmission, carries the workpiece trays into the conveying system. The safety belt is pre-tensioned and bonded during installation to form a continuous safety belt. A safety belt installation kit is used for joining, tensioning, and bonding.
Use the following formula to determine the required belt length.
Note: The belt requires a pre-tension coefficient F.
Pounds = ((2 x height + height + height) x feet) + 60
lB = Belt Length
lS = Section Length
Length of medium conveyed at the LAS drive module
Length of conveying medium at the lUM return device section
F = Pre-stretching coefficient
Pre-tension coefficient F for the belt
BS 2 and lS ≤ 4000mm, F = 0.98
BS 2 and lS > 4000 mm, F = 0.975
In the formula, AS 2/B-250, F=0.965
Conveyor belt length for medium transportation
LUM = 660mm
LAS = 660 mm
Belt Expansion
Among them, lS ≤ 4000 mm = 2%
where lS > 4000mm = 2.5%
Among them, AS 2/B-250 equals 3.5%.
Bosch-Rexroth WI 2 Joystick
For regional monitoring
For workpiece tray identification
Stop device for horizontal conveyance of workpiece trays
Suitable for installation on ST 2/... sections or ST 2/...H sections with a web width of 45 mm or 50 mm, respectively.
Suitable for use in the EPA
A basic arm element for workpiece pallet length ≤ 480mm
Two basic arm elements of the workpiece pallet with a length ≥ 640mm
Joysticks are used in the following areas:
For regional monitoring
Stop device for horizontal conveying of workpiece trays
Used for workpiece tray identification
According to the required functionality, the WI/M, WI 2/... arm should be equipped with one or two sensors.
Bosch-Rexroth rotary lifting device
HD 2, b160, l T160 Lift & Rotate Unit, DW90, h90
3842525849
3842525859
Enhance Rotating Device HD 2
The Z-axis swivel shaft: 90° or 180°. Optionally, the rotation direction of HD 2/90° can be individually driven for each workpiece tray if needed.
The WT lift distance is 40 mm or 90 mm above the transport level. Models with a 40 mm lift are suitable for rotating workpiece trays directly above the conveyor section. If any components, such as identification and data storage modules, are installed on the side of the workpiece tray, a 90 mm lift version may be required.
Maximum allowable total mass moment of inertia: 0.65 kgm²
The HD 2 lift turns the workpiece tray to the desired position. In a system without curves, this device ensures the workpiece tray is always oriented correctly, with the front facing forward at all times. No additional force is required to operate the HD 2.
Required accessories
Brake Pad VE 2/...
M12x1 sensor, rated sensing distance SN ≥ 4 mm, non-flush mounting required, with a 0.5 mm offset
REXROTH Screw Conveyors
Excavator
Excavator, Right Side 3842532679
Excavator, Left Side 3842532680
Used for removing small parts from the conveying medium
Combined with workpiece trays weighing no less than 3 kg.
Conveying Medium: Belt conveyors, toothed belts, and flat-top chains
Can be installed on the right (R) or left (L) side
Reversible operation cannot be achieved on the conveying section equipped with a loader.
REXROTH Damper DA 1/B
Pneumatic damper
Adjustable damping degree
The allowable load of the workpiece tray ranges from 0.5 kg to 6 kg (with a conveying speed of 9 m/min).
When the workpiece tray is moved to the lifting and positioning device HP 1/P, the damper DA 1/B is used to cushion the impact on the workpiece tray.
Suitable for Mounting to HP 1/P
Order Number: 3842535360
Total weight of workpiece trays: 10 kg
Cleanroom Class ISO 7
Drying Room r.F. <1%
Weight: 0.5 kg
Required compressed air interface p 4 ... 6 bar
Pneumatic insertion fit φ 4mm
Rexroth REXROTH Conveyor Belts
GT 2 Conveyor Belt
GT 2, L250 Conveyor, 3842539479
The conveyor belt, used as a medium for conveying, transports workpiece trays to the conveying system. The belt must be pre-stretched during installation and then bonded to form a continuous conveyor belt. The conveyor belt installation kit is used for joining, stretching, and bonding.
The required conveyor belt length is determined using the following formula.
Description: The conveyor belt requires a pre-stretch coefficient F; please refer to the "Conveyor Belt Pre-stretch Coefficient F" overview.
lB= ((2 x lS+ lAS+ lUM) x F) + 60
lB = Conveyor Belt Length
lS = Length of Conveying Section
Length of the conveying medium for the LAS drive module
Length of conveying medium for lUM rotary unit
F = Pre-stretch coefficient
Pre-tension Factor F for Belts
BS2 and IS ≤ 4000 mm, F = 0.98
Among them, BS2 and IS > 4000 mm, F = 0.975
AS 2/B-250, F = 0.965
Belt conveyor medium length
lUM = 660 mm
lAS = 660 mm
Belt Extension
Among them, IS ≤ 4000 mm = 2%
Where IS > 4000 mm = 2.5%
AS 2/B-250 = 3.5%
Rexroth REXROTH conveying medium belt
The belt is made of nylon and features a meshed top, offering conductive properties.
Tension and bond during installation to form a continuous belt
The belt, used as a conveying medium, transports the workpiece trays into the conveying system.
Order Number: 3842539480
ESD
Cleanroom Class ISO 7
Material Data: Polyamide Plastic PA 6.6
Length: 50,000mm
Required Components:
Belt installation kit for connection, tensioning, and bonding purposes.
Adhesive
Belt GT 1, L1000-50000
Rexroth Plastic Flat Top Chain Main Link
Conveying medium for self-assembly of transmission units
For use with ST 2/C and ST 2/C-H sections
Delivery unit length up to 12,000 mm. Multiple flat-top chains connected by the main linkage can achieve a length greater than 12,000 mm.
Nickel-plated steel basic chain version
Steel Chain with PA66 Polyamide Support Cover
The workpiece trays in TS 2plus are paired with the ST 2/C and ST 2/C-H conveying sections.
The required chain length is determined using the following formula.
lC = 2 x lS + lAS + lUM
lC = flat top chain length
lS = Length of conveyor section profile
lAS = Length of the conveying medium within the drive module
lUM = Length of the medium transported in the return device
Length of flat top chain conveyor medium
lUM 2/C-170 = 310 mm
lUM 2/C-60 = 150 mm
lAS = 625 mm
Item No. 3842551226
Material Data: Basic Chain: Steel; Nickel-plated PAl 66 ESD Flat Chain
Length: 12,000mm
Note:
Plastic flat-top chains are also suitable for EPA use but cannot be used on curves and bends.
Workpiece trays equipped with PE wear-resistant pads are not recommended for cumulative operation as this will exacerbate wear.
Plastic flat top chains are not to be used with steel GP sliding profiles.
Recommended Accessories
Additional闭合链节，3842551234
Flat Top Chain Tool
Main connecting rod 3842551234 fits for two plastic flat-top chains
Supply Range
Plastic flat-top chain (l = 12,000 mm, black), including 1 x main rod
Rexroth Coupling Male and Female Ends 3842218920
