Automatic Particle Strength MeasurementPlease provide the Chinese content to be translated into American English.Used to determine the maximum strength during the crushing of various particle shapes. The instrument features digital display and functions such as start, reset, stop, print, and calculate average values. This instrument, developed by integrating the advantages and applicability of various strength measurement devices, is suitable for microcomputers.Automatic Particle Strength Tester。

Automatic Particle Strength MeasurementInstrumentTechnical Specifications

Automatic Granule Strength TesterInstrumentMeasurement Range: 0--20N, 50N, 80N, 200N, 300N, 500N

Resolution: 0.01N, 0.1N (Four-digit display)

Instrument accuracy: 0.5% Sensor accuracy: One ten-thousandth of a Newton

Ambient Temperature: Room temperature to 50℃ Relative Humidity: <85%

Power Voltage: AC 220V ± 10%

Instrument setup parameters and operation instructions:

1. Range: Input the instrument test range according to the pressure sensor's range in the program. Do not set a small range for a large scale.

2. Instrument Calibration: Set the calibration weight on the tuning program, then place the corresponding standard weight, and the displayed value matches the calibration code (in Newtons). The instrument internally uses this value to calculate the full-scale sample value.

3. Sensitivity: The instrument has 1-9 sensitivity levels, with higher numbers indicating greater sensitivity and smaller measured values. Lower numbers are less sensitive to fragmentation, resulting in larger measured values. Generally, levels 7-8 are used, with adjustments possible based on specific conditions.

4. Language: Batch export of instruments, with language differentiation for Chinese and English display and print output.

5. Printing: Print the corresponding strength values in the order of determination.

6. Average Display: The average can only be calculated for the same measurement sample with over 10 measurements. Values exceeding 60% of the average (not within the average range) will be automatically excluded. The "avr" average will be displayed at the end of the printed result.

Automatic Granule Strength TesterStandard testing for:

1. Ensure pre-test preparation is complete, turn on the power switch, the instrument displays 123.4. Wait until it shows 0.0 before the instrument can enter the testing state.

2. Place the sample in the center of the test platform, press the start button, the power indicator blinks, the instrument displays the current test number, starting from 1, the motor operates, the pressure rod moves downward, pressing down slowly, contacting the sample, displaying the current pressure value until the tested sample breaks. Instantly, the motor reverses (moves upward), the instrument displays the maximum破碎 strength of the sample, and the test ends. Prepare for the next test. Conduct 1-30 consecutive tests per sample; if over 30, or if a new sample is to be tested, press the reset button, and continue testing from 1.

3. The reset function.Press the reset button gently.Set the current measurement value to zero, display 0.0 or 0.00, and clear the memory data. The next measurement will start from serial number 1. If the sample diameter is excessively long, it canPress and hold the reset button.The push rod raises a distance.Tap halfway.Print KeyDo not stop the rod from rising at any time. (Do not rotate all the way back; otherwise, the rod may be damaged.)

During the measurement process, Do not arbitrarily press the reset button; otherwise, all the sample data measured previously will be cleared..

1. Printing Function.Tap the print button lightlyWhen the instrument stops working and displays previously saved data, the last displayed number 88 represents the average. If it cannot be calculated, it will show FFF.F.Hold down the print key.Print out the test results, with each test result printed separately, along with the serial number. The last set of data is avr, which represents the average value of this batch of samples.

2. The instrument is equipped with an automatic protection program, which automatically returns to normal when exceeding the measurement range.

3. The relationship between the added weight and the corresponding indication

Manual Sensitivity Adjustment Section:（Soft and hard samples are sensitive to adjustments.,For reference）

Due to the soft and hard measurements of the customer's sample, the required sensitivity may differ from what we need. The instrument can be equipped with a manual sensitivity adjustment feature without being connected to a computer, for the convenience of the customer to modify the sensitivity themselves. Follow the steps below:

1. Press the power button to turn on

2. When the numbers are blinking, press the reset key and the print key to adjust up and down. The reset key is for addition, and the print key is for subtraction. A low reading indicates the sensitivity is too high; reduce the sensitivity. If the material is completely crushed, it means the sensitivity is too low and needs to be increased. The range of sensitivity is determined by your own test values and the actual conditions; setting it to 7 or 8 is usually fine.

3. Press the start button to save, then you can test it.

The calibration and adjustment of the instrument must be coordinated with the manufacturer; it is not allowed to be done independently, otherwise, the consequences will be at your own expense.