Brand safety issues must not be overlooked!
Sign collapses and injures pedestrians, which we've all seen. Thus, signs also require regular maintenance to ensure safety!

That's a huge safety hazard if not maintained promptly!

Shenzhen Zhongjianyuan Engineering Technology Co., Ltd. reminds everyone to pay strict attention to label safety issues!

Now there are many outdoor varieties, including light boxes, storefront facades, roadside billboards, neon lights, and posters, etc. Among them, storefront facades are the most commonly used, and the main component of storefront facades is steel structure. If protective paint is applied, they can usually last 5-10 years. Neglecting maintenance, they won't last more than three years.

To reinforce the sign, Chengdu Jun Du focuses primarily on expansion bolts, followed by the several "feet" of the steel frame structure. This requires regular inspections to prevent any accidental injury incidents.

Additionally, pay attention to the stability of the walls; even the tightest expansion bolts won't fit properly if the walls are loose.

Shenzhen Zhongjianyuan Engineering Technology Co., Ltd. recommends using scientific methods for maintenance to effectively avoid the issues mentioned above.

High Altitude Installation Safety Basics
Persons engaged in high-altitude installation must possess a certain level of operational experience, maintain good physical health, and avoid frequent occurrences of anemia, dizziness, and acrophobia. Regular health check-ups are required.

Preparation for高空 installation

1. High-altitude installations typically require scaffolding. Materials for the scaffolding must be inspected, avoid using severely corroded materials, and ensure that wooden, bamboo, and metal pipes are sturdy.

2. All holes at high-altitude work sites must be covered with sturdy plates, fences, or safety nets.

3. Any work that can be pre-assembled on the ground must be done so, to minimize work at height.

Control Operation Method Prevention

To prevent falling accidents, it is advisable to avoid high-altitude operations where possible, opting for lower-level installation methods instead.

For projects not involving high-altitude work, corresponding measures should still be taken. Strengthen the review and approval process for scaffolding setup plans, as well as the inspection and acceptance after the scaffolding is installed.

2. Workers performing high-altitude tasks are prohibited from wearing high heels, hard-soled shoes, slippers, or other slippery footwear while on duty or under the influence of alcohol. Workers in high-altitude operations should be mindful of their body's center of gravity and the way they exert force to prevent accidents caused by the center of gravity exceeding the support surface.

Shenzhen Zhongjianyuan Engineering Technology Co., Ltd. is qualified for various steel structure parameter inspections, including weld inspection, bolt tensile pull-out testing, coating thickness measurement, deflection testing, steel structure component dimension inspection, steel section inspection, and steel component damage detection. As most signs are made in steel structure form and are constantly exposed outdoors to sun exposure and rain, they are prone to damage. Generally, outdoor steel structure signs require regular inspections and maintenance.

I. Types of safety inspections included in the brand:
Our business scope for building construction structural inspection mainly includes (walls, freestanding signs, rooftop signs).
Label testing content:
1. Specifications for the horizontal and strength indicators of the brand's non-destructive testing base.
2. Overall assembly and welding quality of brand non-destructive inspection.
3. Lightning protection, insulation, and corrosion resistance specifications for brand non-destructive testing.
4. Review of design, approval, installation, and raw material documentation related to non-destructive testing equipment.
5. The impact on the surrounding environment after the brand's non-destructive testing equipment is set up.

Section 2: Brand Engineering Quality, Inspection, and Acceptance Testing:
1. Production Requirements:
Meets CE148:2003, Technical Code for Steel Structures of Outdoor Facilities, and relevant provisions of GB 50017.
② When connecting to the original house structure with bolts or welds, the connection bolts or welds should be calculated based on the overall structural stability against overturning. The calculated stress of the bolts or welds should not exceed 75% of the design bearing capacity.
③ The layout of the connecting parts should be coordinated with the roof column grid, and should be able to directly bear the pressures, uplifts, and shears transmitted from the beam structure.
④   Must have measures to prevent direct lightning, induced lightning, and lightning surge intrusion; the grounding system of the plate structure should form an equipotential connection.
⑤ Steel structures must undergo anti-corrosion treatment.
Material Requirements: Angle steel, pipe steel used for signboards exposed to outdoor environments
The wall thickness of channels and flats must not be less than 3mm, the main steel used should not be smaller than ∟80*8, the angle steel used in welding structures should not be smaller than ∟56*36*4 or ∟404, and the angle steel used for bolt connections should not be smaller than ∟505. The steel pipe for installing light tubes should be no less than 20*20; the light box panel is made of polycarbonate, with 3mm milky polycarbonate used inside and 5mm transparent polycarbonate on the outside. The light source employs standard T4 fluorescent tubes, with the logo section using acrylic vacuum forming and featuring an integrated LED light source.

Brand safety inspections serve as a carrier for outdoor facilities, playing a positive role in a company's product quality, public image, and cultural connotation promotion. Increasingly favored by businesses, outdoor facilities have seen rapid development, with their numbers growing annually and their structures becoming more diverse. Consequently, safety issues are on the rise, making it crucial to conduct routine inspections of the brand's structure each year to prevent accidents.

The mark is a tool in the pull system for initiating the next production process or transferring work-in-progress to the downstream process. This term translates to "種" or "板" in Japanese.
All outdoor media that convey information. The size of the media is determined by the actual environment.
The signage, storefront, and exterior facade can be hand-painted, digitally created, or printed on paper. The materials for the signs are typically made of: square tubes, angle iron, etc., welded together. They can include 3D panels, light fabrics, vacuum-formed plastics, automotive paint, clipboards, aluminum-plastic panels, and more.
Rule Editing
1. Downstream processes order products based on the exact quantity specified on the label.
Brand
Pack (2 pieces)
2. Production of products is carried out according to the exact quantities and sequence indicated on the label.
3. No label, no production or handling of the product.
All parts and materials must be labeled.
Never send defective or incorrectly counted products to the next production station.
6. Be extremely cautious when reducing the quantity of each brand to avoid issues of insufficient stock.