Eye Wash Unit2019Best-selling item.Many businesses have already adopted。
Eye wash basins and shower heads are standard.
Not from other small manufacturersQualityMaterial. Please note for all buyers to differentiate.
Please proceed if you're not just comparing prices without considering quality.
Eye Wash Station Sources and Application Scope
Eye wash stations are a new phenomenon that emerged with the human rights factory inspections by European and American customers, and they have a history of over a decade in our country.
The Hantie Emergency Eyewash and Shower is widely used as an emergency first aid device in oil, chemical, petrochemical, electronic, coal chemical, solar, semiconductor, food and beverage, and other hazardous work areas and laboratories. In the event of chemical liquid or toxic substance splashes on the worker's body, face, or eyes, or in the case of fires causing the worker's clothing to catch fire, this device quickly reduces the level of harm, minimizing the injury to the worker from toxic substances. The emergency eyewash and shower is produced using professional technology, with non-toxic materials, and adheres strictly to the American ANSI/ISEA Z358.1-2009 standard.
Product Advantages
The portable eyewash unit completely solves the issue of space occupation, with zero-space storage being a unique feature of the product. It boasts the following characteristics:
1. Timely provision of professional protection with ease and convenience.
2. No installation required; can be installed on-site as needed or used directly.
3. Wash eyes and face with water, and assist with hand washing if necessary.
4. Material is:Non-toxic polyethylene, Container equipped withExhaust Valve。
 
Product Specifications
Usage Instructions
1. Add Water: Rotate the air compressor handle counterclockwise, remove the air compressor, and add pure water to the container.12 gallonsAfter adding water, simply tighten the nut.
2. Inflate: Pull the handle of the rotary inflation cylinder out of the inflation tube's locking slot, push and pull the handle to begin inflation until the exhaust valve automatically releases air. After inflation, screw the handle back into the inflation tube's locking slot to secure it.
3. Irrigation: Squeeze the hand grip of the eyewash valve to activate water flow. Press the push button to lock the water flow. After irrigation is complete, push the button up to release, and release the hand grip to turn off the water.
Please note:
This product does not come with a drain hole; please pre-arrange a drainage solution.
2. In case acidic or alkaline solutions enter the eyes, first rinse thoroughly with eyewash solution, followed by using an eyewash unit or seeking medical attention.
Please check and inflate regularly (every 3 days, ideally) or replace the water (typically every 5-7 days).
4. If working in an environment with hazards, it is recommended to add a certain amount of professional eye wash concentrate to pure water. This will better ensure protection for the eyes or face, and also extend the retention time of the stored liquid.
 
Eye Wash Station Compliance Standards
ASTM Z358.1-2009
1.1Standard water pressure (0.25Mpa) with a flushing flow rate of ≥ 75.7L/min, continuous flushing for over 15 minutes.
1.2The height of the shower basin from the ground should be between 2083-2438mm.
1.3The height of the water spray from the showerhead is between 2083-2438mm from the ground, with the center of the spray range being a certain distance from any obstacles.DistanceShould be 406mm.

1.4At a horizontal plane 1524mm above the ground, the diameter of the spray water is ≥ Φ508mm.
1.5The handle of the ball valve should not exceed 1733mm (69 inches) from the standing plane of the user.
1.6Eye Wash Water Flow ≥ 11.4 L/min under standard water pressure, with continuous flushing for over 15 minutes.
1.7Eye wash flow rate: 1.5 L/min, continuous rinse for 15 minutes (handheld eyewash units, etc.).
1.8The eye wash nozzle height is between 838-1143mm from the ground, and the distance from the eye wash head to the obstacle (distance from the main pipeline) is 150mm.
1.9Two eye wash nozzles should be spaced 101.6mm apart and evenly distributed between the two parallel center lines (symmetrical about the center).
1.10The flush height is 203mm (8 inches) from the eye wash nozzle.
1.11The eyewash and shower valves can be activated within one second.

Offline Ordering: Please call <17316588755>, WeChat and QQ <3343978197> for order inquiries.