Pulsarlube S100 Spring-Actuated Grease Injector, Miniature Precision Grease Filling System

KLT1500 Single Point Greaser

Comparison of Manual Greasing and Automatic Greasing

Traditional Lubrication Method:

I. Labor

1. Man-hour consumption.

2. Inadequate manual lubrication.

Money:

1. Increase the purchase oil cost.

2. Increased equipment wear due to inaccurate lubrication.

3. Increase equipment upgrade and maintenance costs.

4. Reduce production output.

Automatic Greasing Applicator Greasing Method:

I. Manpower:

1. Reduces labor hours.

2. Equipped with the ability to provide oil at a timed and measured rate.

Two, Currency:

1. Reduce oil procurement.

2. Maintenance equipment costs can be reduced.

Increase equipment reliability.

4. Reduce equipment maintenance time.

Increase production capacity.

6. Accelerate equipment automation. In the context of global competition, the reliability of equipment is both a company's competitiveness and a determinant of profit, as increasing output means increasing revenue. Therefore, regular maintenance and repair of equipment are crucial. Among these, lubrication is paramount, as proper lubrication can reduce equipment wear and tear, thereby cutting down on maintenance costs. This, in turn, can lower a company's operating capital, allowing for more funds to be invested in the company's operations, generating greater profits. Thus, using an automatic grease applicator not only saves costs but also generates revenue, symbolizing a company's progress. How should we determine the amount of lubricant to apply to our equipment's bearings? Firstly, you can consult the lubrication guidelines provided by the bearing supplier, or refer to the following simple setting table.

Axle Diameter, Pulsarlube Setting Time, Manual Lubrication Cycle

> 105mm, 1-2M, lubricate every 1-2 days

88-105 mm, 2-3 M, lubricate every 3-4 days

79-87 mm, 3-4 M, lubricate once a week

63-78 mm, 4-6 M, lubricate once a week

49-62 mm, 6-8 M, lubricate every other week

35-48 mm, 8-10 M, lubricate once a month

35mm, 10-12M, lubricate monthly

When the operating temperature reaches above 70℃, the lubricating grease must be doubled for every 15℃ increase. 2. When the bearing is contaminated, such as with dust, moisture, acidic or alkaline environments, the lubricating grease must also be doubled. 3. When the bearing load is heavy, such as with vibration or pressure, the lubricating grease must be doubled as well. If the operating conditions include all of the above, then the fresh grease must be replenished in an even greater amount to ensure lubrication quality. The bearing should maintain an appropriate space to allow excess grease to be expelled during startup and operation. Moreover, grease has a shelf life; regularly replenishing fresh grease to expel contaminated grease can extend the bearing's quality and lifespan.

Pulsarlube S Automatic Greasing System

The Pulsarlube S Automatic Greaser is a high-tech product from the USA - the Pulsarlube S Automatic Greaser (a reverse-pressure spring-loaded automatic oiler). The Pulsarlube S features a clever new design with a spring at the bottom of the lubricator, which pushes grease up into the lubricator's grease inlet and then down into the guide sleeve, reaching the lubrication point. Shenzhen Sanhe Boda has focused on the lubrication industry for 16 years, providing safe and reliable lubrication solutions for several publicly listed companies. We are an authorized Pulsarlube dealer, purchasing directly from the factory for competitive prices. Our after-sales service system is comprehensive, and the operation is simple and convenient. The upward piston movement of the Pulsarlube S Automatic Greaser prevents grease from dripping out due to gravity, keeping the lubricant intact in the oil gun, thereby preventing the hardening of the grease and allowing the lubricator to be completely emptied.

Pulsarlube S Automatic Greaser Features:

Internal piston clip in lubricator, prevents oil separation during storage

Quick installation (can be pre-filled with oil)

More effective than any other traditional spring-type lubricator

Easy to operate

Available in various dosage ratios for use in any location.

Pulsarlube S Automatic Grease Injector Specifications:

Product Dimensions: Φ67×129(H)mm

Lubricant Capacity: 100ml (90g)

Weight (fully filled): 350g

Operating Temperature: -23℃ to 121℃

Export Thread Size: 1/4" Standard Pipe (Thread)

Model KLT1500

Applicable to: Areas with limited space, suitable for long-distance installation; Locations with frequent high differential pressures; Places with significant vibration, where traditional gas products are not suitable; Areas with severe wear on bearings due to dust or particulate contamination; Places requiring regular lubrication but difficult to lubricate; Locations where lubrication is only possible after shutdown; Areas needing to reduce maintenance costs (such as using distribution valves to supply oil to 2, 4, 6, or 8 lubrication points); All industrial bearings requiring grease; Air conditioning equipment (collectors, blowers); Electric motors, pumps, and rotating equipment; Conveyors, various machinery and equipment; Rotating equipment and air conditioning systems in large buildings; Automotive and electronic industry equipment; Cement industry and mining equipment; Paper and pulp industry; Food industry; Iron and steelmaking industry; Pulsarlube S Automatic Greasing System to reduce machine lubrication maintenance and extend machine lifespan.