Shandong Zhongjie Special Equipment specializes in: fuel (gas) boilers, organic heat carrier boilers, biomass boilers, waste heat recovery boilers, and other boiler products; vacuum insulated cryogenic pressure vessels such as LNG storage tanks, oxygen-nitrogen-argon storage tanks, CO2 storage tanks, etc.; pressure vessel products including denitrification engineering equipment, heat storage and energy storage equipment, and complete chemical equipment; central air conditioning and HVAC equipment such as ground (water) source heat pumps, air source units, water-cooled screw units, and air-cooled modular units. Planned products include large-scale energy centers, LNG transport vehicles, LNG tank containers, and other green energy equipment.
When a gas steam boiler experiences overpressure, the following immediate actions must be taken: 1. Shut off gas supply: First, immediately close the gas supply to cut off the fuel source and stop the combustion process to prevent further increase in steam pressure. 2. Open the pressure relief device: Activate the boiler's pressure relief device, typically a safety valve. The safety valve is a crucial safety feature of the boiler; it automatically opens when the internal pressure exceeds the set value, releasing overpressure steam to reduce the boiler pressure. 3. Reduce the burner load: If the overpressure is caused by excessive burner load, reduce the burner load to decrease steam production and thereby lower the boiler pressure. Adjust the gas supply to the burner or the burner's adjustment method to match the current load requirements. 4. Inspection and maintenance: After an overpressure event, inspect and maintain the boiler to identify the cause of overpressure and make repairs. Possible causes include burner failure, control system issues, valve malfunctions, etc. If necessary, consult a boiler maintenance technician for inspection and maintenance. It is important to note that overpressure is a dangerous condition during boiler operation and must be addressed promptly. When dealing with overpressure, operators should remain calm, follow safety procedures, and ensure their own safety. If unsure how to handle an overpressure situation, contact a boiler maintenance or technical support personnel immediately for assistance.

WNS Low-Nitrogen Condensing Hot Water Boilers offer the following advantages: Low Nitrogen Emissions: The WNS Low-Nitrogen Condensing Hot Water Boiler employs low-nitrogen combustion technology, optimizing the combustion process and burner design to significantly reduce nitrogen oxide (NOx) emissions. This helps to minimize environmental pollution. High Thermal Efficiency: The WNS Low-Nitrogen Condensing Hot Water Boiler utilizes condensing technology, recycling heat from flue gases to enhance thermal energy efficiency. The thermal efficiency of condensing hot water boilers typically exceeds 90%, surpassing traditional hot water boilers. This aids in energy conservation and cost reduction. Safe and Reliable: The WNS Low-Nitrogen Condensing Hot Water Boiler features a control system and safety devices with excellent safety performance. It is equipped with multiple safety protection features, including overheat protection, overpressure protection, and water level protection, capable of automatically monitoring and controlling the boiler's operation to ensure safe operation. High Flexibility: The WNS Low-Nitrogen Condensing Hot Water Boiler is suitable for various applications, including industrial, commercial, and residential settings. It can accommodate different heat load requirements, offering strong flexibility. Additionally, it can be integrated with other systems, such as solar hot water systems and ground source heat pump systems, to further enhance energy efficiency. Easy Operation and Maintenance: The operation and maintenance of the WNS Low-Nitrogen Condensing Hot Water Boiler are straightforward.

A gas boiler is a heating equipment that uses gas or similar fuels. It generates heat by burning gas, heating water into steam or hot water, which is used for heating, hot water supply, or industrial production, among other applications. The working principle of a gas boiler involves mixing gas with air, igniting it to produce high-temperature combustion gases, and then transferring the heat to the water through a heat exchanger, thereby raising the water temperature. Gas boilers offer benefits such as environmental friendliness, safety, and are widely used in residential, commercial, and industrial sectors.

In industrial boiler systems, the critical functional parameters of water pumps include the following aspects: Flow Rate: The flow rate of a pump refers to the volume of liquid it pumps per unit of time. In industrial boilers, the pump must provide sufficient flow rate to meet the boiler's water requirements. The size of the flow rate depends on the boiler's rated evaporation capacity and the design requirements of the circulating water system. Head: The head of a pump is its ability to overcome fluid resistance and lift the liquid to a certain height. In industrial boilers, the pump must have adequate head to ensure smooth flow to all parts of the boiler, including the feedwater system and circulating water system. Power: The power of a pump is the electrical or mechanical energy required to drive the pump. In industrial boilers, the power of the pump needs to be determined based on flow rate and head to meet the system's requirements. Efficiency: The efficiency of a pump is the ratio of the input energy to the output fluid energy. Efficient pumps can reduce energy consumption and operating costs. In industrial boilers, choosing an efficient pump can improve the system's energy efficiency performance. Operation Stability and Reliability: Water pumps in industrial boiler systems must have good operation stability and reliability. The pump should be able to run stably for a long time without being affected by external interference or fluctuations, and should be adaptable to different operating conditions. Pumps should be selected based on the specific industrial boiler system and design requirements, ensuring that the functional parameters meet the system's needs. Additionally, the selection and operation of the pump should adhere to relevant standards and regulations to ensure safe and reliable operation.
Our company attaches great importance to technological innovation and research and development, boasting one municipal-level enterprise technology center in Heze City. We have established testing facilities for non-destructive testing, physical and chemical testing, welding testing, hydrostatic testing, etc. We are equipped with over 600 various instruments and equipment, including CNC machine tools, X-ray flaw detectors, digital ultrasonic flaw detectors, mechanical property testing machines, chemical analyzers, spectrometers, tensile testing machines, plasma welding machines, and more. The key products we have developed, such as welding for temperature and pressure vessels, emissions reduction for biomass boilers, and waste heat utilization, have successively been included in multiple Shandong Provincial Department of Industry and Information Technology science and technology innovation projects, Shandong Provincial key projects, and Heze City innovation and excellence projects. We have cumulatively obtained 27 authorized utility model patents, 16 authorized invention patents, participated in drafting 2 standards, 2 industry standards, and registered 15 trademarks. Our technical team, in collaboration with Professor Li Yajiang of Shandong University, has developed deep cryogenic container processing technology using the international plasma arc + filled wire argon arc welding (PAW-GTAW) technology, which has been appraised as an internationally competitive level in the field of deep cryogenic container manufacturing at the provincial level.
Choose ZJET Customized Solutions, join hands to create brilliance together!