Shandong Zhongjie Special Equipment (formerly Heze Boiler Factory Co., Ltd.) was established in 2001, located at No. 2218 Jinnan Road, Development Zone, Heze City, with a registered capital of 50 million yuan and total assets of 500 million yuan. The company has 7 business centers: boilers, deep-freeze containers, pressure vessels, central air conditioning, engineering installation, international trade, and Internet of Things. It has three factory sites on Jinnan Road, East Changjiang Road, and Bohai Road, covering a total of 200,000 square meters, with the main workshop area being 83,000 square meters. It currently employs 710 people, including 247 engineering and technical personnel and 82 middle-level technical personnel. In December 2016, it was recognized as a "High-tech Enterprise" by the Science and Technology Department. In June 2021, it was identified as a "Specialized and New Enterprise in Shandong Province" by the Ministry of Industry and Information Technology. In June 2022, it was recognized as a "Deer Enterprise in Shandong Province" and in August 2022, it was identified as a "Specialized and New Small Giant Enterprise" by the Ministry of Industry and Information Technology.
A gas thermal oil boiler is a device that uses gas as fuel to heat thermal oil through the heat energy produced by combustion. Here are some basic facts about gas thermal oil boilers: Working Principle: The working principle of a gas thermal oil boiler involves mixing gas with air, then burning it to produce high-temperature flue gas. This flue gas is then passed through the flue and heat exchanger to exchange heat with the thermal oil, transferring heat energy to the thermal oil and raising its temperature. The thermal oil circulates within the boiler, transferring heat energy to the equipment or process that requires heating. Thermal Oil: The thermal oil used in gas thermal oil boilers is typically an organic heat carrier, such as mineral oil or synthetic oil. It has high thermal conductivity and thermal stability, allowing it to operate stably at high temperatures and transfer heat energy to the heated equipment. Gas Combustion System: Gas thermal oil boilers are equipped with a gas combustion system, including burners, gas supply systems, and control systems. The burners mix gas with air and burn it to produce heat. The gas supply system is responsible for providing gas and adjusting the supply quantity as needed. The control system monitors and controls the gas combustion process to maintain stable operation. Safety Protection Devices: Gas thermal oil boilers are equipped with various safety protection devices to ensure the safe operation of the equipment. Common safety protection devices include overheat protection, overpressure protection, and water level protection, which monitor and control the boiler's operation to prevent equipment damage and safety accidents. Application Fields: Gas thermal oil boilers are widely used in industrial sectors such as chemicals, textiles, food processing, and papermaking. They can provide stable high temperatures for various applications.

The flow rate standard for the heat-conducting oil in the oil tubes of a thermal oil furnace typically varies based on specific application and equipment requirements, with no unified fixed value. Generally speaking, the flow rate of the heat-conducting oil within the tubes should be maintained within a reasonable range to ensure the normal operation of the equipment and the effectiveness of heat transfer. Excessive flow rates of the heat-conducting oil can lead to issues such as increased system pressure loss, higher pump power consumption, increased friction losses in the pipes leading to energy loss, and increased system noise and vibration. On the other hand, low flow rates can result in insufficient heat transfer, affecting the equipment's thermal efficiency, prolonged residence time of the heat-conducting oil in the pipes, which can lead to oxidation and thermal decomposition, shortening the oil's lifespan, and the formation of carbon deposits in the pipes, increasing resistance and affecting fluid flow. Therefore, when designing and operating a thermal oil furnace system, it is necessary to consider specific equipment parameters, the properties of the heat-conducting oil, and pipeline layout, among other factors, to determine an appropriate flow rate. Typically, the flow rate should be within the range of 0.5-2.0 m/s, but the specific figures should be adjusted and optimized based on actual conditions. In practice, the flow rate can be controlled by monitoring and adjusting the pump flow and pipe resistance to meet the equipment's heat energy needs and operational requirements.

To optimize and improve the planning of gas boiler systems, consider the following aspects: 1. Energy Audit and Assessment: Conduct a comprehensive energy audit and assessment to understand the energy consumption of the gas boiler system and identify potential energy-saving opportunities. Through data analysis and energy measurement, determine the main sources of energy consumption and bottlenecks to provide a basis for subsequent optimization. 2. Combustion System Optimization: Optimize the combustion system of the gas boiler, including adjustments and cleaning of burners, control of the ratio of gas to air, and maintenance of the combustion chamber. Ensure high combustion efficiency and high gas utilization to reduce energy waste. 3. Heat Recovery Utilization: Consider installing heat recovery devices such as waste heat recovery units or flue gas heat exchangers. These devices can utilize the excess heat in the flue gas emitted by the gas boiler to heat water or other equipment requiring heat, improving energy efficiency. 4. Pipe Insulation and Leak Inspection: Ensure that the insulation performance of gas and hot water pipes is good to reduce energy loss. Regularly check for pipe leaks and repair them promptly to avoid energy waste and safety hazards. 5. Control System Upgrade: Consider upgrading the control system of the gas boiler to adopt automated control technology. Through control and regulation, achieve optimal operation of the gas boiler.

Safety requirements for steam boiler valves mainly include the following aspects: Valve Selection: Choose the appropriate type and specification of valves for steam boilers. Valves should comply with relevant standards and specifications, and possess characteristics such as high-temperature resistance, pressure resistance, and corrosion resistance. Valve Installation: Valves should be properly installed in the corresponding position of the steam boiler. During installation, ensure the connection is firm, the seal is reliable, and leaks and loosening are prevented. Valve Operation: The operation of valves should be convenient, flexible, and capable of accurately controlling steam flow and pressure. The handle or device should indicate the opening and closing direction of the valve, as well as the corresponding operation method. Valve Sealing: The sealing performance of valves is crucial. Valves should have good sealing properties to prevent steam leakage and energy loss. The sealing surface should be flat, smooth, and able to withstand high temperatures and wear. Valve Maintenance: Regularly inspect and maintain valves to ensure their normal operation and safety performance. This includes cleaning valves, checking sealing surfaces, lubricating moving parts, and promptly repairing or replacing damaged components. Safety Valve: A safety valve must be installed on the steam boiler to protect its safe operation. The safety valve should comply with relevant standards and specifications and be capable of automatically opening when exceeding the set pressure to release overpressure steam, preventing boiler explosions. Valve Identification: Valves should be marked with their type, specification, working pressure, and flow rate information. This helps operators correctly identify and operate valves, avoiding incorrect operations and accidents. It should be noted that the above safety requirements are general guidelines, and specific safety requirements should be determined based on the type, scale, and operating environment of the steam boiler. When using valves, follow relevant laws, regulations, and safety operation procedures to ensure the safe operation and effective control of valves.
ZJ Special Equipment upholds the grand vision of "realizing employees' dreams, creating value for customers, and striving for the prosperity and strength of our motherland," and is dedicated to the development of the green energy equipment industry. We offer society high-value products and services!