1. Pre-job Preparation: (1) Position the suction truck as close as possible to the work area and park. (2) Adjust the drain valve handle of the return oil tank to a 45° angle relative to the axis of the intake pipe, observe the intake pipe for lubricant flow, and inquire about the horsepower of the Yuchai engine in Hunan Tianjin High-pressure Cleaning Trucks. (3) Open the side door of the walkway box, remove the suction hose, ensuring it swings backward without any kinks. 2. Suction Operation: (1) Insert the suction hose as deeply as possible into the waste liquid, ensuring the tip remains below 300mm from the liquid surface throughout the operation. (2) Push the four-way valve handle perpendicular to the ground. (3) Shift the transmission to neutral, then start the engine, disengage the clutch, pull the power take-off switch backward to engage the gear, and the vacuum pump begins to operate. (4) Open the tool box in the cab, pull out the buzzer switch, and connect its power supply. (5) The operator can use the observation mirror on the top of the rear cover. When the liquid level reaches the middle of the mirror, notify the driver. Quickly pull the suction hose away from the ground or close the four-way valve. In normal circumstances, the buzzer will emit an audio-visual signal at this point. Upon receiving the signal, the driver should reduce throttle, push the power take-off switch forward to disengage, stop the vacuum pump, press the buzzer switch, and disconnect its power supply. (6) Close the fuel tank by aligning the drain valve handle parallel to the axis of the intake pipe. (7) After rinsing the hose, place it back in the walkway box, close the side door, and position the boom toward the top of the cab. (8) Close the overflow valve, ensuring the handle is perpendicular to the road axis. (9) Drive the suction truck away from the work area. What types of new high-pressure cleaning trucks does Chengli offer? How many horsepower does the Yuchai engine in Hunan Tianjin High-pressure Cleaning Trucks have?

Equipment consists of clean water tanks and sludge tanks, primarily used for cleaning and unblocking urban pipelines; the clean water tank and sludge tank are two separate tanks. Use the clean water tank for cleaning and the sludge tank for suction, but not both functions simultaneously. The tanks cannot be fully loaded at the same time. Tank dimensions (length of straight section × diameter) are 4700×1950mm, with the front section being the clean water tank (length of straight section × diameter) 2050×1950mm; the rear section is the sludge tank (length of straight section × diameter) 2650×1950mm, with a useful volume of 7.6 cubic meters for the sludge tank and 6 cubic meters for the clean water tank; side protection material is Q235, bolted connection; rear lower protection material is Q235, welded connection, with the rear protective device cross-sectional dimensions (width × height) being 50×200mm, and the rear protective height from the ground is 400mm; ABS system model/manufacturer: J ABS/Jiaozuo Borike Control Technology Co., Ltd.; it uses a 4500mm wheelbase; optional exhaust treatment device with the chassis. How much is a Yunnan 40 cubic meter high-pressure cleaning truck? Can a blue license plate high-pressure cleaning truck be registered to an individual?

Five: Suction Truck Vacuum Pump Accessories: The hydraulic oil separated by the oil-water separator of the suction truck is reused as the lubricating oil for the vacuum pump, but the separated water remains at the bottom of the tank. Therefore, it is necessary to drain the water after the suction truck operation is completed. Forgetting to drain can cause the water to be吸入 into the pump, leading to issues like sticking. Long-term use of hydraulic oil can reduce its lubricity and airtightness. Hence, the hydraulic oil in the suction truck should be changed regularly. Six: Suction Truck Overflow Preventer: The overflow preventer on the suction truck is installed to prevent wastewater from spilling into the vacuum pump in case the tank is full. If the vacuum pump吸入 too much sludge, it can easily be damaged. Therefore, it is important to regularly check the condition of the overflow preventer during the operation of the suction truck. Seven: Suction Truck Rear Tank Door: After long-term use, the clamping installation inside the rear tank door of the suction truck accumulates dirt, making it impossible to tighten the handwheel. Thus, it should be disassembled and cleaned every six months, and it is advisable to add lubricating grease at this time. It's also a good idea to clean the sealing gasket of the rear tank door after the operation of the suction truck. If there are leakage issues and the tightening mechanism is checked and found to be in good condition, the sealing gasket of the rear tank door may need to be replaced, as prolonged use can reduce its sealing effectiveness.

1. This vehicle is designed for cleaning and suction, with main equipment including a clean water tank, waste water tank, high-pressure water pump, and water circulation suction pump. Tank dimensions are (length of straight section × diameter) (mm): 4700×1950, with the front section being the clean water tank (length of straight section 2050mm) and the rear section being the waste water tank (length of straight section 2650mm). The water tank and suction tank are two separate tanks; the clean water tank is used for cleaning, and the waste water tank is used for suction. Both functions cannot be used simultaneously, and the tanks cannot be fully loaded at the same time. The waste water tank has a net volume of 7.6 cubic meters, medium: liquid waste, density: 800 kg/cubic meter; the clean water tank has a net volume of 6.0 cubic meters, medium: water, density: 1000 kg/cubic meter. 2. The vehicle uses a 4700mm wheelbase. The relationship between the overall length, front overhang, wheelbase, and rear overhang (mm) is as follows: side and rear protective materials are Q235, connection method is welding, cross-sectional size 300×50mm, lower edge height from ground 480mm. 3. Equipped with a driving recorder with satellite positioning function. ABS model/manufacturer: 3631010-C2000/Dongke Kogel Commercial Vehicle Braking System ( Shiyan) Co., Ltd., ABS 8/Dongke Kogel Commercial Vehicle Braking System (Shiyan) Co., Ltd., 4/Weber Automotive Control Systems (China) Co., Ltd. Optional cab with chassis, optional different engines and corresponding exhaust after-treatment system layout, optional rear winch style, optional front auxiliary engine with roller shutter door structure on the tank. What is the horsepower of the engine for the Jiefang chassis high-pressure cleaning vehicle?

Chengli Special Vehicle Co., Ltd. Sales Branch 13 is located in the hometown of Emperor Yan Emperor神农, the land of ancient chime music, "Capital of Special Vehicles" - the plains of the south suburbs of Suizhou City, Hubei Province. It is a manufacturer of various special vehicles and an independent export enterprise. It is a domestic manufacturer of special vehicles for Suizhou's landscaping, petrochemicals, municipal sanitation, and pressure vessels, with the registered trademark "Chengliwei" brand, product code: "CLW". A key partner of Dongfeng and Jiefang companies, it is mainly engaged in the production and manufacturing of various special vehicles, and also sells whole vehicles and parts from various large manufacturers. The company has the right to export independently, and its products occupy a large share of the international market. The leading products include compactor garbage trucks, sweeping trucks, hook arm garbage trucks,对接 garbage trucks, flatbed transport trucks, water-spraying trucks, tanker trucks, garbage trucks, fecal sludge trucks, sludge trucks, dump trucks, box trucks, semi-trailers, tow trucks, winch trucks, aerial work vehicles, training vehicles, bulk cement trucks, chemical trucks, fire trucks, auto parts, concrete mixer trucks, and trailers, among which the eight main series include... What undercarriage is used for the rear eight-wheel high-pressure cleaning trucks? How many horsepower does the Hunan Tianjin high-pressure cleaning truck have with Yuchai engine?

Dongfeng D9 Yuchai 200HP chassis high-pressure cleaner. How many horsepower is the Yuchai for Hunan Tianjin high-pressure cleaner?

Sewage Suction Truck Product Main Technical Parameters Product Name: Sewage Suction Truck Exterior Dimensions: 8000, 8550, 8750, 9050, 9350, 9650×2500×3300 (mm) Chassis Model: CLW5180GXE6 Body Dimensions: ×× (mm) Total Weight: 18000 (Kg) Rated Weight: 9770, 9705 (Kg) Curb Weight: 8100 (Kg) Maximum Speed: 105 (km/h) Emission Standards: GB3847-2005, GB17691-2018, China VI Chassis Parameters Chassis Model: EQ1185LJ9CDE Fuel Type: Diesel Axle Count: 2 Wheelbase: 3600, 3950, 4500, 4700, 5000, 5300, 5600, 3600 (mm) Tyre Count: 6 Axle Load: 6500/11500 Tyre Specifications: 295/80R 22.5 18PR, 10.00R 18PR, 275/80R 22.5 18PR Engine Parameters Engine: Dongfeng Cummins Engine Co., Ltd. Displacement (ml): Power (kw) B6.2NS6B 210D 4.5NS6B 220D 4.0NS6B 195YCS04200-68CY4SK761B 6.2NS6B 230YCY30165-60 Hunan Tianjin High-pressure Cleaning Truck Yuchai Horsepower

Chengli Special Vehicle Co., Ltd. is committed to the transportation industry, striving for high-quality management through technological innovation. Since its establishment, the company has been involved in livestock transportation vehicles, water-spraying trucks, garbage trucks, and oil tankers, serving as the main force in transportation. Chengli Group always influences and drives the team to success with an honest and steady spirit and the unwavering belief in victory. Chengli Group remains attentive to the transportation market, achieving win-win growth with clients through keen market insights.