Sliding busbar channel installation
Sliding busway trays are used to accommodate fixed or movable branch devices. They are employed on active production lines to supply power to motors or portable tools that move along with the production line, or for operators who need to move within a 5-meter range to perform specific operations.
Busbars can only be installed in open and visible locations. If there is a passage that meets the following conditions, installation behind the distribution panel is permitted. Overcurrent devices are not installed on the busbars except for single lighting fixtures. The space behind the panel is not used for air conditioning. Busbars are completely sealed and non-ventilated. The installation of busbars makes it easy to maintain joints and accessories between sections. Busbars should not be installed in places prone to severe mechanical damage, corrosive steam, or crane loading/unloading areas. For special-purpose devices, busbars can be installed in hazardous areas, outdoors, or in damp locations. The spacing of busbar supports should not exceed 10 meters. For special installations, the spacing of horizontal busbar supports can reach 25 meters, and the spacing of vertical busbar supports can reach 40 meters.
In areas where the busway runs through the floor and is less than 15 meters from the floor surface, the busway must be completely enclosed and properly protected to prevent mechanical damage. If the joint is outside the wall, the busway can be routed through the wall.
Features
Due to the use of copper or aluminum as conductive materials in busbars, they offer high current capacity and excellent electrical and mechanical properties. Additionally, being encased in a metal槽, they are non-combustible, highly durable, and have a long service life. Compared to traditional distribution equipment, they significantly reduce the required space and have an aesthetically pleasing appearance, making them highly advantageous for construction and distribution in large buildings. In summary, busbars possess the following characteristics:
1. Current capacity can be quite large; busbars are made of T2 electrolytic copper, and currents ranging from 250A to 6300A can be achieved. Particularly suitable for the power requirements of modern buildings.
2. Minimal voltage drop; due to high conductivity, the loss is small, copper strip bending machine sales, voltage drop is very minimal.
3. High short-circuit load capacity; can withstand large short-circuit currents.
4. High reliability and long lifespan; under normal conditions, the lifespan can reach over 60 years. In the long run,iCompared to cables, it's quite economical.
5. High safety; the busbar槽 has high safety due to its mechanical strength, effectively protecting the copper bars inside from damage. Additionally, the high protection grade further enhances safety.
6. Environmentally Friendly & Energy Efficient; busbars have no secondary pollution, ensuring environmental protection and energy efficiency.
7. Compact size; high current, small volume.
8. Lightweight and easy to operate; compared to cables of the same capacity, the busbar trunking is significantly lighter.
9. Connection is extremely simple (similar to connecting water pipes, with sections connected through tees, elbows, and other fittings to form a system); wiring is flexible, the Yancheng Copper Strip Bending Machine is easy to use.
10. Construction and inspection are simple; subsequent maintenance is more straightforward and effortless.
11. Features modern aesthetics. The aluminum magnesium alloy housing is sleek and tidy.
Features of the collector:
No electric shock risk even when touched with fingers, in compliance with IP23 standard.
2. Energy-saving and consumption reduction, using special formula aluminum alloy profiles as conductors; low resistance, capable ofiLarge ScaleiReduce power loss.
3. Long service life, with a formulated conductor sheath that extends the lifespan of the sliding wire system.
4. The electrical collector can move in three-dimensional space, ensuring uninterrupted power supply to the power equipment; features dual insulation design, seeking to purchase a copper strip bending machine for enhanced operation.
5. New materials, technologies, and processes ensure the product boasts enhanced corrosion resistance, weather resistance, and operating temperature range, with improved performance.
6. Light series ≤500A, Heavy Type I series 630A-1250A, Heavy Type II series >1250A; the same series, sheath and accessories are interchangeable.
7. Features a combination design for easy installation and daily maintenance, particularly suitable for high-altitude operations.
Conductor manufacturers inform us that a collector is a new type of power supply system for mobile machinery and equipment, featuring special alloy aluminum profiles as conductors, with an outer sheath made of a special polyethylene material.iRaw material for烯, providing safety against rain, dust, snow, and electric shock. Simple structure, easy installation and maintenance, widely used for power lines of mobile equipment in mines, metallurgy, chemical industry, machinery, docks, and cargo yards.
Copper Bar Bending Machine Price - Kai Di Electric (Online Inquiry) - The Yancheng Copper Bar Bending Machine is provided by Suzhou Kai Di Electric Co., Ltd. Suzhou Kai Di Electric Co., Ltd. has dedicated much passion and enthusiasm to the field of electronic and electrical product manufacturing equipment. Kai Di Electric has always been customer-centric, creating value for customers, and winning the market with quality and service. We sincerely hope to cooperate with all sectors of society to create success and brilliance together. For related business inquiries, please contact Cai Yan.
