Silver ion antibacterial agentRUCO-BAC AGL
Product Ingredients: Inorganic Salts and Surfactants, Anionic.
Application Field: Suitable for antibacterial finishing on all types of fibers, particularly for intimate fabrics.
-Antibacterial and mild antifungal properties.
-Washable and dry cleanable; limited washability on polypropylene.
-Does not affect hydrophilicity.
-Compatible with fluorescent whitening agents and most auxiliaries; please pre-test for compatibility before use, especially when used in conjunction with cationic products.
-Anti-yellowing
-Please provide the Chinese content to be translated.pHValue3 - 11Stable within range.
-In compliance with the European Biocidal Products Directive registration, German registration number:N-29625；
-Active ingredients (non-finished product) by the U.S.FDACertification, applicable in the following fields:
-21CFR 175.105 Adhesive
-21CFR 175.300 Resin Coating
-21CFR 176.170 Moist and fatty foods
-21CFR 176.180 Dried food
-21CFR 177.2600 Rubber
-21CFR 175.320 Polyolefin film
-Creamy suspension
-20°CApproximately at the time ratio1.1 g/cm3
-pHApproximately7
-Easily soluble in cold or warm water
RUCO-BAC AGLBefore adding to the ingredient hopper, pre-dilute and stir with cold water to ensure uniformity. The solution must be pre-filtered and used immediately. Due to the product's sensitivity to light and tendency to settle, avoid prolonged storage.
Ensure the fabric to be processed (especially bleached or light-colored fabrics)pHThe value is nearly neutral; non-volatile acids (such as citric acid) or acid-releasing agents may be used.RUCO-ACID ABSAdjustment.
Dipping and rolling process
5 - 20 g/1 RUCO-BAC AGL(Simple Antimicrobial Treatment)
20 - 50 g/1RUCO-BAC AGLHigh-Efficiency Antimicrobial Treatment
Non-volatile acids (such as citric acid) or acid releasersRUCO-ACID ABSAdjustable fabricpHValue up to4.5-5。
Flow rate of rolled liquid60 - 70 %
Drying100- 170 °C
Suction technology
0.5 - 2.0 % RUCO-BAC AGL(Simple Antimicrobial Treatment)
2.0 - 5.0 % RUC O-BAC AGLHigh-Efficiency Antimicrobial Treatment
Bathing Ratio10 : 1
Non-volatile acids (such as citric acid) or acid-releasing agentsRUCO-ACID ABSAdjustable fabricpHAs valued4.5 - 5。
Temperature40 - 50℃
Time15-30 min
Then drain (no rinse required).100- 170 °CDrying.
The product may foam in high-speed overflow equipment (such as jet dyeing machines).
For Polypropylene
The product is used for100 %Polypropylene's antibacterial effect has limited wash resistance.
Alkaline washing treatment
Fabric treatedRUCO-BAC AGLIf retouching is needed after sorting, severe color change may occur if hot alkali washing is used.
To prevent this occurrence, you can add to the alkali wash solution
1 - 2 g/L VEROLAN NEB
This issue does not arise in high-temperature household washing, as the detergent contains special composite ingredients.
RUCO-BAC AGLCompatible with water and oil repellent finishing agents. However, in some cases, the water and oil repellent properties may be affected when using a one-bath process. This can be compensated by appropriately increasing the dosage of the water and oil repellent finishing agent.
If sharing the bathRUCO-BAC AGLPhoto-catalytic FreshenerRUCO-FRESH ACSThe brightness of the fluorescent whitened fabric may decrease to varying degrees. It is recommended to conduct a preliminary trial.
RUCO-BAC AGLWith catalystMgCl2Incompatible. When in use with resin-embedded baths, we recommend usingRUCO-BAC AGP。
One-bath processRUCO-BAC AGPTo prevent agglomeration, each product must be pre-dissolved in water.
Thoroughly stir before use.
The aforementioned information is compiled based on our company's comprehensive research and practical experience. We assume no responsibility for third-party intellectual property rights or German extraterritorial laws. Users must conduct their own tests to determine if this product and its application process meet their specific requirements. We are not liable for any uses or applications not formally submitted in writing to our company. For technical and commercial inquiries about this product, please contact our office.
