Epoxy Self-Leveling, Wide Color Selection, Abrasion, Alkali, and Corrosion Resistant, SP1138

SP-Solvent-Free Epoxy Antistatic Topcoat

Product Number: SP-1119

The appearance is smooth and glossy with a variety of colors.

Surface resistance: 1×10^6 Ω to 1×10^9 Ω, excellent and durable antistatic effect.

3. Durable and easy to clean.

4. Resistance to alkali, salt, and oil corrosion.

5. Quick installation, low odor, and affordable pricing.

Product Introduction:

A solvent-free epoxy antistatic floor coating is a two-component, roller-applied, seamless high-performance thin-film eco-friendly conductive epoxy floor coating produced from imported raw materials. The coated surface is smooth, attractive, and durable.

Performance Features:

The appearance is smooth and glossy with a variety of colors.

Surface resistance: 1 x 10^6 Ω ~ 1 x 10^9 Ω, excellent and durable antistatic effect.

3. Durable and easy to clean

4. Resistance to alkali, salt, and oil corrosion;

5. Quick installation, minimal odor, and low cost.

Application Scope:

This product's surface resistance ranges from 1×10^6 Ω to 1×10^9 Ω, suitable for industries requiring high cleanliness, aesthetics, dust-free, sterile, and antistatic conditions, such as electronics, microelectronics, communication products, computers, precision instruments, textiles, printing, and large-scale precision instrument factories, as well as military, aerospace, and other fields.

● Main Technical Parameters: [Specific data see inspection report]

Item

Technical Specifications

Color and appearance

Uniform color, smooth and flat

Drying Time (25℃) - h

Table dry

≤

8

Diligence

≤

48

Hardness (Shore hardness, D-type)

≥

75

Wear Resistance (750g/500r)

≤

0.03

Impact Resistance (50 cm·kg)

Coating free of cracks and flaking

Water resistance (168h)

Non-bubbling, non-flaking, slight color change permitted

Saltwater resistant (3% NaCl, 168h)

Non-bubbling, non-peeling, slight discoloration permissible

Alkaline resistance (20% NaOH, 72h)

Non-bubbling, non-flaking, slight color change permissible

Fuel-resistant (120#, 72h)

Non-bubbling, non-flaking, slight color change permissible

Acid resistance (10% H2SO4, 48h)

Non-bubbling, non-flaking, slight color change permissible

Volatile Organic Compounds Content (VOC), g/L

≤60

Surface Resistance (Static Dissipative)

1×106Ω～1×109Ω

Note: 1. The above technical specifications are measured under standard conditions (25°C, 60% humidity) for reference only.

2. Drying rates vary significantly with temperature and humidity, also affected by factors like paint film thickness, ventilation, and underlying coatings. Generally, higher temperatures lead to shorter drying times, while lower temperatures extend them.

● Installation Instructions:

Mixed: A component to B component = 4:1, mix thoroughly and evenly after blending.

During construction, the curing temperature should be between 10-35°C, with relative humidity below 80%, and the base surface temperature should be at least 3°C above the dew point of the air; otherwise, construction is prohibited. Use winter type below 20°C and summer type above 20°C; the moisture content of the concrete base should be less than 6%. Ensure the construction area is well-ventilated and dust-free, but avoid strong winds to prevent dust from affecting the appearance. This product is not suitable for direct sunlight or areas with high UV intensity.

Ø Usable Time: Approximately 30 min (at 25℃); the usable time after mixing decreases with higher temperatures. Not suitable for application when the ambient temperature exceeds 35℃.

Theoretical Consumption: 0.2~0.3 kg/m² (Consumption is for reference only; actual values may vary in specific projects due to ground conditions, environmental factors, construction techniques, color, and other factors. Please refer to on-site measurements for assessment.)

Recommended Thickness: 0.15~0.25mm (dry film thickness)

Installation Method:

Roll Coating  Large-scale application, medium to long-fiber wool roller used

Spraying Both conventional and airless spraying equipment are acceptable.

Brush painting  Recommended for small areas, use a soft bristle brush.

Ø Diluent: Not required; if the construction environment temperature affects the construction difficulty, it is necessary to consider the environmental conditions for use. Under the guidance of Xiupu technology, an appropriate amount of SP-8302 diluent may be added as needed.

Tool Cleaning: SP-8302 Diluent B

Ø Recoating Interval: Apply the next coat only after the previous coating has completely dried, typically with a 24-hour interval under standard environmental conditions (25°C, 60% RH).

Recommendation System:

System Structure

Product Model

Consumption: kg/m²

(As applicable)

Construction Method

Primer

SP-1205H Solvent-Free Spreading Epoxy Primer

0.12-0.3

Scrape coating, roll coating

Primer (multiple coats)

SP-1206H Solvent-free Spreading Epoxy Intermediate Coating

0.1-1

Scraping coating

Conductive layer

Copper foil is laid according to design, and grounding connections are installed.

Anti-static intermediate coating

SP-1215 Antistatic Epoxy Primer

0.15~0.45 in two passes

Scrape coating

Anti-static face coating

SP-1119 Solvent-Free Epoxy Antistatic Paint

0.2~0.3

Roll coating, spray painting, brush painting

Note: Consumption figures are for reference only and may vary due to ground conditions, environmental factors, construction techniques, and color, etc. Please use on-site measurements for assessment. The types and processes of the specific coating system may be adjusted according to usage requirements and construction environment; please consult a professional from Xiupu.

● Packaging Specifications:

25 kg/set

Component A: 20kg/bag, Component B: 5kg/bag