Electro-hydraulic Push Rod DYTP2000-500/2.2KW Parallel Cylinder

Electro-hydraulic Push Rod DYTP2000-500/2.2KW Parallel Cylinder

Electro-hydraulic push rods are powered by an electric motor, which, through forward (reverse) rotation, drives hydraulic oil to be output as pressure oil through a bidirectional gear pump. The oil then travels through an integrated oil block to the working cylinder, achieving reciprocating motion of the piston rod. Advantages: 

1. ...Features overload automatic protection: During the operation of the electro-hydraulic actuator, if the external force on the piston rod exceeds the rated output force or the piston reaches the end position, the motor continues to rotate. At this point, the oil pressure in the circuit increases to the set pressure, and the overflow valve quickly and accurately discharges, achieving overload automatic protection. Although the motor is still rotating, ...    Will burn.2. Self-locking Function: The oil circuit module of the electro-hydraulic push rod is designed with a pressure self-locking mechanism, so when the motor stops rotating, the piston rod immediately remains stationary.  The pressure oil is in a pressure-holding state at the position.3. Infinite Adjustment: Can be infinitely adjusted according to customer requirements within the specified speed, output force, and stroke range.

Model DescriptionThe electro-hydraulic push rod primarily consists of six key elements: the push rod's type, the motor's protection grade, rated output force, stroke, rated speed, and usage angle. It can also be customized according to customer requirements.   Requirements: Equipped with three adjustment functions, namely: speed adjustment (push and pull), force adjustment, and stroke adjustment (stroke switch positioning). In addition to the aforementioned three adjustment functions, please specify at the time of ordering:   Please note the text, and fill in the six key elements carefully, referring to the model coding method for the rest.DYTZ Type Integrated Vertical Electro-Hydraulic Push Rod Technical Specifications (Selection Chart)

ModelRated Output Power (10N) Rated Speed (mm/s) Motor Model Stroke Manufacturing Range (mm) Stroke Manufacturing Range (mm)

ThrustTension Speed, Pull Speed, Traction Rate

DYTZ450-/110 450 310 110 140 Y802-4-0.75KW 50-800 10-110 

DYTZ700-/110 700 510 110 140 Y90S-4-1.1KW 50-1500 10-110 

DYTZ1000-/110 1000 750 110 140 Y90L-4-1.5KW 50-1500 10-110 

DYTZ1750-/90 1750 1300 90 115 Y100L1-4-2.2KW 50-2000 10-90 

DYTZ2500-/90 2500 2050 90 115 Y100L2-4-3KW 50-2000 10-90 

DYTZ3000-/90 3000 2500 90 115 Y100L2-4-3KW 50-2000 10-90 

DYTZ4000-/80 4000 2950 80 100 Y112M-4-4KW 50-2000 10-80 

DYTZ5000-/60 5000 3300 60 90 Y112M-4-4KW 50-2000 10-60 

DYTZ6000-/60 6000 3800 60 90 Y132S-4-5.5KW 50-2500 5-60 

DYTZ7000-/50 7000 4500 50 75 Y132S-4-5.5KW 50-2500 5-50 

DYTZ8000-/50 8000 5000 50 80 Y132M-4-7.5KW 50-2500 5-50 

DYTZ10000-/40 10000 6500 40 60 Y132M-4-7.5KW 50-2500 5-40 

DYTZ15000-/35 15000 11000 35 45 Y132M-4-7.5KW 50-2500 5-35 

DYTZ20000-/25 20000 15000 25 35 Y132M-4-7.5KW 50-2500 5-25 

Note:1. The motors listed above are rated at 380V, with an IP44 protection rating.     Yarn gradeB Grade. 2. For travel manufacturing ranges or speed manufacturing ranges exceeding those listed, please specify otherwise, the technical parameters within the table will be used. 3. The speed range listed in the table is for horizontal use; the speed for upward or downward use is half of the horizontal use. 4. The typical number and power listed in the table indicate that the push rod of this model has the rated output force and speed.   Power at high values. Motor power is proportional to pushrod force and speed.

Safety Precautions for Installation and Use

The hydraulic push rod installation requires sufficient space, with an environmental temperature between 10-60 degrees Celsius (special order required for high-temperature environments).

2. Users can configure journey switches as needed for control.

3. Prior to installation, the electric hydraulic push rod should be placed flat on the ground and filled with hydraulic oil (brand HM, accuracy grade 46-68). The oil level should be below the inspection port, and the oil surface of the split rod should be within 50mm from the box.

Before using, turn the exhaust screw of the exhaust port on DYDTZ, DYTP, and DYTF counterclockwise 2 turns.