Voltage Stabilizing Harmonic Filter

DN-V Series Voltage Stabilizing Harmonic Filter

One,Product Overview

Currently, voltage sag is prevalent among various electrical power quality issues.Or too highA frequently occurring, severely harmful power quality issue.Based on the power systemStatistics indicate that voltage dropsOr overvoltageUser complaints accounted for80% plus, due to harmonics and switching operationsThe lowVoltageOr high voltageConsumer complaints regarding power quality issues are not reaching us. 20%。

Common voltage sagOver-voltageThe reasons are as follows:FiveSpecies:

1) Fault current-induced voltage sag：During a short-circuit fault in the transmission or distribution network, current sharply increases, causing voltage drops at the common voltage connection points. Simultaneously, these voltage drops propagate through the power grid, disrupting a large number of users.

2) Voltage sag caused by inductive motor start-up：When the induction motor starts under full voltage, the voltage value it needs to draw from the system is the same as when it's running at full load.5-10 times, this high current flowing through the system impedance will cause voltage sag.

3) Voltage dip due to lightning and lightning strikes，Lightning-induced flashovers of insulators and ground discharges in the lines are the primary causes of voltage dips in the system. During the rainy season or in regions prone to thunderstorms, equipment exposed to the open air is easily disrupted by lightning interference.

4）Voltage fluctuations caused by low or high power factor.No performance.PowerIn the systemCan cause line failuresThe voltageWastageThis isCapacitiveNo effectIncreasePower supplyVoltage:Reason。

5）Unpredictable偶然incidents: construction roadwork, traffic accidents, human errors, etc.

Two,Product Applications

1、Semiconductor Industry (Chip Manufacturing, Testing, and Packaging)

2、New energy industry (including multicrystalline silicon, monocrystalline silicon drawing, battery testing, aging, and encapsulation, etc.)

3、Medical Equipment Industry (detection instruments, radiotherapy and chemotherapy equipment, liquid phase analyzers, etc.)

4、Automotive manufacturing industry (automatic welding, painting, baking, etc.)

5、Food and Beverage Industry (food baking, packaging, canning, bottling machines, etc.)

6、Petroleum industry (pumps, refineries, drilling rigs, etc.)

7、Textile Industry (screen printing machines, winding machines, hoisting machines, etc.)

8、Smart Factory Industry

III.Product Features

1. Suppress dynamic and steady-state voltage dropsWith voltage increase、EliminateSurgeEliminate voltage fluctuationsFlicker

2. Features good dynamic voltage stabilityStableCapabilityOutput voltage accuracy achieved±1%；

3. EffectivelyFiltering stagesHarmonicsThree-phase imbalanceEnhancePower factor, improve power supplyPower quality.

4. The stabilizer features ideal energy-saving effects, ranging from 1% to 8% in different field conditions.

FourProduct Performance Specifications

1、Stable Harmonic FilterInput Voltage:Single-phaseVoltageAC 220V±15%   Three-phaseVoltageAC 380V±15%

2、Stable Harmonic Filter Output Voltage: Single-phaseVoltageAC 220V±1%    Three-phaseVoltageAC 380V±1%

3、Nominal Frequency50Hz/60HUniversal

4、Dynamic Voltage Range:60%-110%) UN    Stable Voltage Range:90%-110%) UN

5、VoltageApplianceDynamic Response5ms

6、Power FactorCOS≥0.95 and above

7、Harmonic suppression times adjustableSelect specific sub-harmonics（3, 5, 7, 11, 13, 15, 17, 19, 21, 23, 25 times)

8、Stable Harmonic FilterAvailableDynamic reactive power regulation, power factor compensation up to0.99Rapid response time≤20ms。

9、Total Harmonic Distortion (THD)THDi≤Less than 10%, Total Harmonic Distortion Voltage THDu≤4%Below,

10、Stable Harmonic FilterPower Factor Correction (PFC) FilterDynamic Response≤20ms

11、Cooling Method: Forced Air Cooling

12、Ingress Protection Rating:IP30/IP35 or higher ratings are required to be specified prior to order placement.

13、Wiring method    Three-phase, four-wireSeries connection (see Figure)1, Image2）；

14、Cooling Method:     Forced air-cooling

15、Communication Interface:   RS485Communication InterfaceModbusCommunication Protocol

16、Noise Level:   Rated power output≤60dB(Distance from equipment)1mSection

Five,Product Model Description

Six.Product Installation Wiring Method

Single-phaseAC220V Stabilizer Wiring Diagram

Three-phaseAC380V Stabilizer Wiring Diagram

Section 7:Product Model Specifications Selection Table

Or higher power, please inform in advance. Non-standard sizes available for re-design.

Non-standard or higher power ratings for on-site loads are acceptable; please inform in advance. Non-standard dimensions will be redesigned.