Sporwei Epoxy Resin Anchoring Adhesive - Excellent bonding strength, shrinkage reduction, and durability.

Spor-Weld Planting Adhesive

Spoway Anchor Epoxy boasts high bonding strength, resembling pre-buried anchors, cures at room temperature with minimal shrinkage during hardening, excellent temperature resistance, can be welded after embedding the steel bars, good durability and weather resistance, anti-aging, and resistance to media.(Acid, alkali, water)High performance, exhibits excellent toughness and impact resistance after curing, free of volatile solvents, non-toxic, and environmentally friendly.A、BWide ratio of group allocation adhesive, easy to apply, and features. It belongs to structural reinforcement material.

One.Features:

1Room temperature curing, high bonding strength, strong adhesion, and excellent durability.

2Excellent resistance to aging and good acid and alkali resistance.

3Excellent resistance to water and other mediums.

4Available for export,The ratio of the B component is wide, facilitating on-site operation.

5The rear steel bars exhibit superior load-displacement characteristics, akin to pre-buried reinforcement.

6Excellent heat resistance, suitable for welding after embedding steel bars.Two.Application Scope:

1.Reinforcement and screw anchoring in various building structures, structural strengthening and reinforcement, and anchoring in building frame and shear walls.

2.Basic equipment fixation, reinforcement for railway, highway, bridge, and water conservancy reconstruction projects

3.Billboards, tunnel pipelines, elevated road noise barriers, and guardrail fasteners

Reaction time

Three.Usage Instructions:

Key Points for Planting Reinforcement Bars and Screw Rod Construction:

Punch holes as per regulations→Clean holes with a brush and an air compressor.→TranslateA、BComponents to be mixed thoroughly and evenly→Proportionally mix and thoroughly blend the rebar bonding adhesive→Inject adhesive into the holes using a tool.→Insert steel bar or bolt by rotating it into the hole.→Cure→Quality Inspection

1.In accordance with engineering design specifications, on the base material(As concrete)Drill holes at the corresponding positions; the hole diameter, depth, and steel bar diameter should be determined by professional technicians or on-site testing.

2. Clean the dust in the drilled holes with a gas strut, a bristle brush, or a compressed air machine; it is recommended to repeat the process no fewer than3No dust or clear water should be present inside the bore.

3.Rust removal treatment is applied to the surface of the reinforcing steel and usedDiluentOr clean with alcohol wipes.

4.Please provide the Chinese content to be translated.A、BComponents by2:1Blend proportionally and mix until completely uniform, then inject into the drilled holes.

5.Rotate the rebar and insert it to the bottom of the hole, ensuring the hole is overflowing with glue and paying attention to prevent any leakage. The fullness of the glue layer will directly affect the size of the anchoring force.

6.Avoid disturbing the fasteners during the curing process; fully cure at room temperature after gelation.1-2Day.

7.Visual inspection of curing condition.现场 pull-out tests are required for the rebars in critical areas to verify if the anchoring force meets the design requirements.;Qualified before proceeding to the next production process.

Four.Technical Specifications:

Rebar diameter(d)(mm) Drilling Depth(mm) Suggested Drilling Diameter(D)(mm) Tensile force(KN)

Ф8 110 12 ≥15  Ф10 150 14 ≥22  Ф12 180 16 ≥37Ф 14 210 18 ≥50 Ф16 240 22 ≥65 Ф18 270 25 ≥85 Ф20 310 28 ≥105 Ф22 350 30 ≥127 Ф24 500 35 ≥160 Ф28 560 40 ≥185 Ф30 600 42 ≥210

Note:Concrete strength grade:C30;To increase tensile anchoring force, use higher-tensile bolts and deepen the hole.

Five.Cautionary Notes:

1.Thoroughly mix and clean the drilling holes; strictly prohibited from disturbing the rod before it sets.

2.You must have protective gear such as gloves, masks, and goggles while working on the construction site.

3.If accidentally contacted with skin or clothing, wash thoroughly with water.ThinnerWash and rinse thoroughly with plenty of clean water.

4.In case of accidental ingestion or eye contact, seek medical attention immediately.

Do not return the mixed residual colloid to the container. To accelerate or slow down the curing speed of the anchor adhesive, simply adjust the curing agent by adding or reducing it appropriately. Remember to store the adhesive in a cool place and tightly close the bucket lid after use.

Six.Packaging Specifications:

1.ABComponent Drum Packaging

2.AComponents12kg/BarrelsBComponent6kg/Bucket

Seven.Transportation and Storage:

1.This product is non-toxic and non-hazardous, and should be transported as general chemical building materials.

2.Do not expose to sunlight, rain, or be inverted during transportation.

3.A、BTwo components should be stored separately to prevent mixing.

4.This product is at room temperature.(5~25℃)Store in a dry place, shelf life12Month(s).

Eight.Adhesive Ratio:A、BGrouped rubber proportion:2:1