Section 1: Product
I. Product Performance
1The plastic water tower is formed using rotational molding technology.
2Our plastic storage tanks are made from imported extrusion blow molding special material, linear low-density polyethylene (LLDPE).LLDPEIt can contain most inorganic acids, bases, salts, and many organic substances at room temperature.
3Components are configured according to the usage provided by the customer.PP、PVC、ABSConnectorPP、PVC、PEFittings are available for selection. When containing acidic or alkaline substances, it is necessary to配备PVC、PPOrPEAccessories and acid-resistant O-rings. When containing organic materials (organic solvents), use non-soluble rubber O-rings.
4The softening point of the plastic used is:
5This product is not suitable for containing strong oxidizers and good organic solvents.
6Other products include:PEFood drums, food box drums, biogas digester drums,周转 boxes, and other plastic container products. Products included as a gift.50And below connectors2Each unit includes a free installation adapter. The product can be customized to open and process according to customer requirements.7Our company specializes in manufacturing large and extra-large plastic containers, with a complete process and a one-time, fully formed structure. Products include:PETanks, chemical storage tanks, mixing drums, transport tanks, drums, and rectangular boxes.PECustom-shaped machining services.
Section 2: Installation and Usage Instructions
1、 The foundation for installing the storage tank must be level and capable of withstanding the corresponding pressure. If a steel structure is used, the gaps should not be too large, and wooden or iron plates should be laid on top.
2、 Tanks storing chemicals should be equipped with proper drainage ditches and dilution facilities around the site.
3、 Due to the inevitable bulging inward of the tank's bottom during the molding process, the foundation must be shaped into a similar spherical crown (it is recommended to lay sand on a level base to form a spherical crown corresponding to the tank's bottom).
4、 Large-scale storage tanks must be installed with safety in mind, and cranes should be used as much as possible. If unsure, please contact us.
5、 Plastic connectors are tightened at the factory, but they may loosen during transportation and handling. Therefore, it is essential to inspect the sealing performance of the connectors before use. You can add liquid above the connector and observe for any leaks. For storage tanks containing chemical liquids, first test for leaks with water to prevent significant losses.
6、 Tubes connected to the bottom of the tank or flanges must be perpendicular to the barrel wall, and soft connections should be used preferentially to avoid uneven expansion of the barrel wall from top to bottom upon filling with liquid, which can lead to damage of the joint and leakage. In severe cases, it may even damage the joint and the barrel itself.
7、 When the liquid inlet is high above the tank bottom, the inlet should bend towards the tank wall to allow the liquid to flow down the wall, reducing impact on the bottom.
8、 Large-capacity storage tank20Above cubic meters, metal reinforcing sleeves can be used to limit the expansion and deformation of the drum at the joint, thereby preventing cracking at the hole.
9、 When installing heavier accessories such as mixers on drums, or when personnel need to work on the drum lid and it cannot bear their weight, please set up a platform or a personnel ladder, and pay attention to work safety.
10In cases where the liquid level cannot be controlled, an overflow outlet should be installed to prevent liquid from spilling out through the manhole, causing unnecessary harm.
11When the inflow and outflow flow rates are high, a corresponding exhaust pipe should be installed.
12Please contact our company again when changing the packaging for liquid products.
Section 3: Main Products
Nanning Tianyi's main products include:PETanks, plastic tanks, chemical storage tanks, corrosion-resistant tanks, plastic water towers, cone-bottom drums, plastic round drums, plastic square boxes, dosing boxes, float tanks, collision barriers, water blocks, pickling tank processing, steel-lined plastic products, plastic containers, plastic custom shapes welding, transportation tank welding, glass fiber reinforced plastic (GFRP) exhaust treatment equipment, and GFRP large containers; also undertake various custom shape processing.
