One,Structure and Composition
Made of coated non-woven fabric, consisting of a hooded jacket and pantsOne-piece structureStandard Type/Seal Strip。
Two,Application Range of Product
Biological hazard managementMildAcid and alkali chemical treatment, pollution removal, disease control/Epidemic management, industrial cleaning and maintenance, wastewater purification, nuclear industry radiation particle protection、Provide barrier and protective gear for handling potentially infectious patient blood, body fluids, and secretions during work.
Section Two:Key Product Performance
1）Critical areas of protective clothing should have a hydrostatic pressure not less than1.67 kPa（17 cm H2O）；
2）The moisture vapor transmission rate of the protective clothing material should not be less than2500g/（㎡•d）；
3）Protective suits must not allow synthetic blood to penetrate through.Grade 2 (1.75 kPa)
4）Outer side of protective suits should have a water resistance level no less than3rd grade requirements
5）The tensile strength of the critical parts of the protective suit material should not be less than45N；
6) The elongation at break for the key parts of the protective clothing material should not be less than 15%.
7) The protective clothing should have a filtration efficiency of not less than 70% against non-oily particles for critical areas and seams.
8) Flame Retardancy (if applicable): Charring length not exceeding 200mm; afterglow time not exceeding 15s; smoldering time not exceeding 10s;
9) The charge of protective clothing should not exceed 0.6μC per piece.
10) The antistatic decay time of protective suit materials shall not exceed 0.5 seconds (if applicable).
11) Total bacterial colony count ≤200 CFU/g, total fungal colony count ≤100 CFU/g.
Section 3:Cautionary Notes, Warnings, and Advisory Information
Please read the instructions carefully.Valid Period60 months, please.Use within the validity period.
2) Non-sterile protective suits are not to be used in areas with strict microbial control standards.
3) This product is for single-use only; reuse is prohibited.
4）After product use, disposal should be conducted according to environmental protection department requirements.
FourInstructions for Use
1) Choose the appropriate size/ specification according to your body type before use.
2) When wearing protective clothing, start with the pants, then put on the shirt, secure the hat, and zip it up.
3) After donning the protective suit, ensure that the head, wrists, and ankle openings are securely covered.
One,Structure and Composition
Made of laminated non-woven fabric, consisting of a hooded jacket and pants, in a one-piece structure: standard type/hook type.
Section II: Product Application Range
Biological hazard management, mild acidic/alkaline chemical handling, pollution removal, disease/epidemic control, industrial cleaning and maintenance, wastewater purification, nuclear industry radiation particle protection, barrier and protective gear for potential infectious patient blood, body fluids, and secretions encountered during work.
Two,Main Product Performance
1) The static water pressure at critical areas of the protective suit should not be less than 1.67 kPa (17 cm H2O).
2) The moisture vapor transmission rate of the protective suit material should not be less than 2500g/(㎡•d).
3) Protective clothing should have a synthetic blood penetration resistance of at least level 2 (1.75 kPa).
4) The outer side of the protective suit must meet the requirement of at least a 3-grade water resistance level.
5) The tensile strength of the key parts of the protective suit material should not be less than 45N.
6) The elongation at break of the key material in protective clothing should not be less than 15%.
7) The filter efficiency for non-oily particles on the critical parts of protective clothing and seams should not be less than 70%.
8) Flame Retardancy (if applicable): Charring length not exceeding 200mm; afterglow time not exceeding 15s; smoldering time not exceeding 10s;
9) The electrostatic charge on protective clothing should not exceed 0.6μC per piece.
10) The static decay time of protective suit material shall not exceed 0.5 seconds (if applicable).
11) Total bacterial colony count ≤ 200 CFU/g, total fungal colony count ≤ 100 CFU/g.
ThreeCautionary Notes, Warnings, and Advisory Information
Please carefully read the instructions for use, valid for 60 months, and use it within the validity period.
2) Non-sterile protective clothing is not used in areas with strict microbial control standards.
3) This product is for single-use only; reuse is prohibited.
4) After product use, disposal should be conducted in accordance with environmental protection department requirements.
Four,Instructions for Use
1) Select the appropriate size/ specification according to your body type prior to use.
2) When putting on the protective suit, first wear the pants, then the shirt, followed by the hat, and zip it up.
3) After donning the protective suit, ensure that the head, wrists, and ankle openings are securely covered.
