Style of cement mortar spraying machine
8. If the pump output pressure is insufficient during work, the booster stator bolts can be adjusted or the booster rubber sleeve and booster worm can be replaced.9. Before spraying, the sprayed area should be permeated with water; When spraying, the nozzle should be perpendicular to the sprayed surface as much as possible (the distance can be adjusted according to the spraying effect) and sprayed evenly in layers, and coordinated with the leveling process. If the wall is too dry or sprayed for too long, it will seriously affect the leveling effect, and the process needs to be changed10. The material should be evenly loaded into the hopper without interruption. When the conveying screw rotates, it is strictly prohibited to use sticks to stir inside the hopper to prevent injury.11. Once the spray conveying pipe is blocked, switch the switch to manual position, only turn on the compressor, remove the quick connector in front of the pump head, and then block the nozzle downwards. The air pressure generates reverse pressure, blowing out the remaining slurry from the conveying pipe. After installing the quick connector, start normal operation.12. When operating a spray shooter, they should wear safety helmets, protective goggles, protective clothing, and other protective equipment.13. The booster rubber sleeve and booster screw are vulnerable parts. In order to extend their service life, the booster stator bolts are in a loose state during initial use. When the pressure decreases and the flow rate significantly decreases, the tightening bolts should be adjusted to ensure that they are in normal working condition.
Description of cement mortar spraying machine
1. It is strictly prohibited to start the machine and run it idle in a state where there is no water or material in the hopper. 2. When the shutdown time is too long, the equipment should be wiped clean, the booster screw should be removed, oiled and stored properly for reinstallation when used again. 3. If the mortar is too thick or the resistance is too high when the machine is running without air, it is easy to cause an increase in motor load, abnormal noise, and pipe blockage. At this time, it is necessary to immediately stop the machine for inspection and adjust the mortar thickness in the hopper. 4. After working for a long time, if mortar overflows from the transmission part or abnormal noise is found, the machine should be stopped immediately for inspection, the mechanical seal should be replaced, and maintenance and repair should be carried out to avoid causing greater equipment damage. 5. When the pump output pressure is insufficient during work, the booster stator bolts can be adjusted, or the booster rubber sleeve and booster screw can be replaced. 6. Before spraying, the sprayed wall surface should be soaked thoroughly with clean water to avoid affecting the bonding degree with the mortar. When spraying, the nozzle should be as perpendicular as possible to the sprayed surface, and the spraying distance can be adjusted according to the spraying effect; It should be sprayed evenly in layers and coordinated with the leveling process. When the wall is too dry or sprayed for too long, it will seriously affect the leveling effect, and the operating procedures and processes should be changed at any time. 7. When loading materials into the hopper, they must be evenly distributed and not interrupted. When the conveying screw rotates, it is strictly prohibited to use sticks to stir in the hopper to prevent injury and accidents. 8. Once the mortar conveying pipe is blocked, the switch can be switched to the manual position, only the air compressor is turned on, the joint in front of the pump head is removed, and then the spray is blocked downwards to generate reverse pressure from the air pressure, thereby blowing out the remaining slurry in the conveying pipe. After installing the connector, it can start working normally. 9. The booster hose and booster screw are vulnerable parts. To extend the service life, the bolts of the booster stator should be in a loose state during initial use; When the pressure decreases and the flow rate significantly decreases, adjust the clamping bolts to ensure they are in normal working condition. 10. During sandblasting operations, staff should wear safety helmets, protective goggles, work clothes, and other labor protection equipment.
Customized cement mortar spraying machine
Consumers born in the 1980s and 1990s grew up in the digital age, and their consumption habits and aesthetics are different from those of the 1960s and 1970s. Young people have a stronger sense of independence and freedom, and are more inclined to pursue fashionable and personalized products. According to a dealer, "More and more young people are buying wall mortar spraying machines now,In addition, from the perspective of the overall market situation, as long as wall mortar spraying machine enterprises are good at discovering the psychological needs of construction contractors, creating new brand concepts, and finding the right market direction, they can gain a foothold in the vast market, which is both the darkness before dawn and the light after dawn. The mortar spraying machine has almost no floor ash, which saves water and materials and can reduce costsMore than 20%. Multi functional, capable of spraying almost all paste materials and liquid materials. Fast speed, high efficiency, and low labor intensity, one (multi-functional speed regulating) spraying machine can easily spray 150 square meters per hour. Excluding preparation time, if working for 8 hours a day, it can spray more than 1000 square meters, which is equivalent to the workload of 20 skilled workers working hard for a day. Small investment, high returns. If each multi-functional speed regulating spraying equipment sprays 1000 square meters per day, calculated at a market average price of 4 yuan per square meter, excluding worker wages of about 500 yuan, each equipment can earn a profit of 3000 yuan per day. Excluding other factors, an annual income of over 500000 yuan is also expected.
