Introduction to Cable Stripping Machine

1. Start the motor and check if it is running normally. When feeding, check the diameter of the rubber cables wrapped around each gear and feed them one by one.

2. In order to make the blade durable for a long time, the joint of the rubber cable should be cut off when feeding to prevent the blade from breaking due to a notch.

3. If there is excessive depth and wire breakage after the feed is discharged, pay attention to the following situations:

① Adjust the tightness of the M12 screws on both sides of the blade shaft on the feeding gear;

② Check if the position is placed incorrectly during feeding;

③ Check if the blade has been replaced and if the edge is too sharp. Use a specialized oilstone to slightly trim it until it is moderately adjusted.

4. If the rubber has been peeled off after feeding, but the copper wire cannot be ejected. There are four main situations:

① If the rolling pattern on the upper shaft is too deep, a special oilstone should be used to grind the upper shaft, but excessive grinding is not allowed. Excessive grinding can easily cause oily cables to be difficult to transmit;

② Is the spring pressure too loose? The pressure should be tightened and stopped as soon as it can be released;

③ If the diameter of the wire is too small or the gap between the upper and lower shafts is too large, the gap between the two shafts should be adjusted to 0 4---0 . 6mm ;

④ The processed rubber cable has already heated up, and the copper wire cannot be ejected.

5. If the pressure gear cannot drive the cable through after feeding and the material stays in the middle, there are several situations that may occur:

① Check if there is any looseness in the belts of each gear;

② Check if the spring pressure on both sides of the gear is too tight and there is no pushing force. The pressure should be relaxed; ③ The cable is too oily, causing the two shafts to slip. The two shafts should be wiped dry regularly (when wiping, please pay attention to safety if the machine is running).

Description of cable stripping machine

Power-on operation:

If the rubber has been peeled off after feeding, but the copper wire cannot be ejected. There are four main situations:

① If the rolling pattern on the upper shaft is too deep, a special oilstone should be used to grind the upper shaft, but excessive grinding is not allowed. Excessive grinding can easily cause oily cables to be difficult to transmit;

② Is the spring pressure too loose? The pressure should be tightened and stopped as soon as it can be released;

③ If the diameter of the wire is too small or the gap between the upper and lower shafts is too large, the gap between the two shafts should be adjusted to 0 4---0 . 6mm ;

④ The processed rubber cable has already heated up, and the copper wire cannot be ejected.

If the pressure gear cannot drive the cable through after feeding and the material stays in the middle, the following situations may occur:

① Check if there is any looseness in the belts of each gear;

② Check if the spring pressure on both sides of the gear is too tight and there is no pushing force. The pressure should be relaxed;

③ The cable is too oily, causing the two shafts to slip. The two shafts should be wiped dry regularly (when wiping, please pay attention to safety if the machine is running).

Customized cable stripping machine

Transmission gears (from slow to fast), 1st gear L - --1, 2nd gear L - --2, 3rd gear H - --1, 4th gear H - --2. Note that the transmission must be stopped when shifting gears.

In terms of operation, there are several situations worth noting about this machine:

① When the machine is working, special attention should be paid to the safety of both hands. When processing sheathed wires and horizontal head operations, the operator's mind should be focused, and a safety cover must be installed in the middle part.

② When processing sheathed wires and cables of various grades, the pressure should not be too tight, and overloading should not be carried out to avoid affecting the service life of various parts.

③ If the material cannot be driven during feeding, check whether the belt is loose, whether the pressure is too tight, or whether the position of the knife is in the wrong direction.

④ If this machine is operated under heavy load for a long time, the oil level of the transmission should be checked every quarter, and the four teeth at the transmission shaft should be lubricated with butter every shift.

⑤ The four Z208 bearings of the upper and lower main shafts should be checked regularly to ensure that the bearings and shafts are not damaged during external transportation. If this phenomenon occurs, they should be dismantled and repaired in a timely manner. Otherwise, if used continuously, it will cause the shaft to easily break.

⑥ When lifting the upper axis for work, the height of both sides should be relatively parallel.

⑦ The four lifting screws of the transmission and the four lifting screws of the motor should be adjusted one by one frequently to check for looseness. If this is the case, the tension of the chain and V-belt should be adjusted and tightened in a timely manner. When adjusting, the gearbox or motor should be relatively parallel and not too tilted.