Wuxi Inken Construction Technology Co., Ltd. Basic Business: 1. Undertake the following projects: structural reinforcement and strengthening of buildings: reinforced concrete beams and columns with carbon fiber, increased cross-sectional area reinforcement of beams and columns, rebar anchoring reinforcement, steel plate bonding, aramid fiber bonding, tunnel steel ring reinforcement, rebar anchoring, bonded steel plates,粘贴 carbon fiber fabric, crack repair, waterproofing and leak repair, steel structures, concrete cutting, bridge lifting, replacement of supports, bridge maintenance and reinforcement, bridge carbon fiber bonding, bridge replacement, etc. 2. Product Sales: structural adhesives, rebar adhesives (both injection and bulk), steel plate bonding adhesives, carbon fiber adhesives, resins, chemical anchors, carbon fiber fabrics, grouting adhesives, joint filling adhesives, grouting materials, carbon fiber boards, etc.
Carbon Fiber Fabric Application Method
1. When bonding carbon fiber materials, the following conditions must be met:
2. Carbon fiber materials should be cut according to regulations.
3. Temperature, air humidity, and moisture content on the surface of components meet the requirements.
4. Bottomcoat and putty are touch-dry (resin surface reaches a solid, hard set).
5. The type of adhesive resin should match the temperature during application. The main agent, hardener, and curing accelerator should be weighed accurately according to the specified ratio, placed in containers, and mixed thoroughly with a stirrer. The mixed quantity should be used up within the specified time.

Dali 300g Carbon Fiber Fabric - 3K Carbon Fiber Fabric Manufacturer Phone Number


When it comes to structural reinforcement, carbon fiber reinforcement cloth is likely a familiar term. It is favored by many due to its numerous advantages. In practice, however, the reinforcement cloth itself doesn't produce such great results; it is primarily the help of the impregnating resin that achieves this. If the resin's strength is insufficient or the quality is poor, the reinforcement effect will vanish when the carbon cloth peels off or gets damaged, and it may even threaten the entire building's safety.


Apply base adhesive. Mix the main agent and hardener in a ratio of 3:1 (or other proportions) and sequentially place them in the container. Measure with a spring scale, mix evenly with an electric mixer, determine the amount based on the actual temperature on site, and strictly control the application time. Generally, use up within 1 hour. Apply the base adhesive evenly to the concrete surface using a roller brush. After the adhesive has cured (curing time depends on the site temperature, touch-dry as a standard), proceed with the next step. The curing time is usually 2-3 days. Leveling. Fill in concave areas of the concrete surface and fill in areas with height differences at template joints, etc., to minimize height differences. Also, round off the corners to a smooth radius of not less than 30mm. Paste carbon fiber cloth. Cut the carbon fiber cloth according to the required size and number of layers. Unless otherwise specified, the length of the fiber cloth should generally be within 3 meters. Mix and apply the surface adhesive (use the same method as the base adhesive), then apply it evenly to the area to be粘贴. Apply more at lap joints, concrete corners, etc. Paste the carbon fiber cloth, peel off the release paper after confirming the correct location, roll it repeatedly with a special roller along the fiber direction to remove air bubbles and ensure the adhesive fully penetrates the fiber cloth. Repeat the above steps for multi-layer pasting, and only proceed with the next layer after the surface of the fiber cloth is touch-dry. Apply the surface adhesive evenly to the surface of the last layer of carbon fiber cloth. The lap length of the fiber cloth along the fiber direction should not be less than 100mm. Secure the ends of the fiber cloth with transverse fiber cloth or steel adhesive for protection and reinforcement. The surface of the reinforced fiber cloth should be protected with plaster or fire-resistant coating.

The company boasts a professional team. We consistently uphold reasonable pricing, integrity, prompt service, and considerate care. Inken Reinforcement Materials is your reliable choice. In our continuous development, we always aim for technology, quality, and诚信 service, meeting the ever-evolving market and customer needs, and contributing to the development and application of high-tech building reinforcement products!