Materials Required for TELEC Certification:

Technical Type Specification Form

(2) Quality Management System Declaration

(3) Method of control and approval for quality certificates or ISO9001 certification (Letter of Quality Compliance)ntrol Confirmation MethodorManufacturer’s ISO 9001 Certificate）

(4) Structural Protection Approval Certificate (Letter of Compliance)nstruction Protection /confirm/iation）

Rated Power Declaration

(6) Antenna Report

(7) Test Reports (including Test Results, Test Setup Photos, and Examinations Conducted)

     (8)(Block Diagram, Schematic Diagram, Bill of Material, Parts Placement, IC Data Sheets, Internal and External Photos, Product Description, User manual,Operational/Technical Description, Description of Pheripherals/Accessories) 

(9) Label Information (Label Location, Label Content)

    If you act as agentoras authorized representative of the manufacturer:

(10) Power of Attorney / Authorization Letter

Note:

All submitted documents are recommended to be in Japanese, although English documents are also acceptable. Test reports may be in the language used by local testing institutions.

2. TELEC is Japan's mandatory certification for wireless products, somewhat akin to China's SRRC. It adheres to Japan's Radio Law. The specific test specifications follow the MIC (Ministry of Internal Affairs and Communications, Japan) Notice No. 88 regulations.

3. The testing items for WiFi and Bluetooth products are basically similar to the European standard EN300 328. For 2.4GHz WiFi products (802.11b/g, 2412~2472 MHz) and Bluetooth products, the standard is MIC Notice No. 88 Annex 43. However, for the 14th channel (Channel 14: 2471~2497 MHz) of the 2.4GHz WiFi products, a separate test and report must be issued using Annex 44.

4. The testing standards for 5GHz WiFi products (802.11a, 5180~5320MHz, W52 Band and W53 Band) are in accordance with Annex 45; however, it's important to note that documents indicate that the MIC will soon revise Annex 45 to include 5.6GHz devices (Band W56) under it, and impose stricter DFS testing requirements for Band 56.

2.4G Product TELEC Certification Required Documents:

1. System block diagram

2. System Schematic

3. User Manual

4. Operation Instructionsnal description）

5. Bill of Materials (BOM)

6. Module Schematic

7. Module Block Diagram

8. Module Specification

9. ISO 9001 Manufacturer Certificate

Label and location diagram (label location label sample drawing photos)

Antenna Specification Sheet: Includes antenna name, type, large gain, measurement chart, appearance, and dimension diagram.

Please note that all provided materials must be in English or Japanese.

TELEC Certification Process:

WLAN and Bluetooth Product Receives TELEC Certification

TELEC is a mandatory certification for wireless products in Japan, similar to China's SRRC. It adheres to Japan's Radio Law. The specific testing standards are in accordance with MIC (Ministry of Internal Affairs and Communications, Japan) Notice No. 88 regulations.

WiFi and Bluetooth product testing projects are essentially similar to the European standard EN300 328.

The standard used for the 2.4GHz WiFi products (802.11b/g, 2412~2472 MHz) and Bluetooth products is MIC Notice No.88 Annex 43; however, for the 14 channels of the 2.4GHz WiFi products,

Bluetooth Product TELEC Certification Testing Project:

Frequency Error Measurement

2. Coupled Bandwidth/Spectral Bandwidth and Spread-Spectrum Bandwidth/Factor Testing

3. Unwanted Emission Intensity Measurement

4. Antenna Power Error Testing

5. Limitation of Collateral Emission of Receiver Measurement Test

6. EIRP Antenna Power Measurement (Transmission Antenna Gain Testing)

7. 3dB Beamwidth Measurement for Transmission Radiation Angle Width

8. Duty Cycle Testing

9. Retention Time Test

TELEC Certification Cycle

The TELEC certification process typically takes 3-4 weeks.