Supply Electric Stop Valves J941H-16C DN500 Electric High-Temperature Steam Stop Valves, Directly from Manufacturer
Product Features
Product advantage
Performance Parameters Table:
Parameter Name Model | Nominal Torque N·m | Torque Control N.m | Control Torque N·m | Allow passage through valve rod diameter | Manual gear ratio | Output Speed: rpm | Motor Power: kW | Weight: Kg |
DZW5 | 50 | 75 | ≤25 |
28 |
1:1 |
18 | 0.12 | |
DZW10 | 100 | 150 | ≤50 | 0.18 | ||||
DZW15 | 150 | 225 | ≤75 | 0.25 | ||||
DZW20 | 200 | 300 | ≤100 | 40 | 0.37 | |||
DZW20I | 28 | |||||||
DZW30 | 300 | 450 | ≤150 | 40 | 0.55 | |||
DZW30I | 28 | |||||||
DZW45 | 450 | 675 | ≤225 |
48 | 24 | 1.1 | 100 | |
36 | 1.5 | |||||||
DZW60 | 600 | 900 | ≤300 | 24 | 1.5 | 103 | ||
36 | 2.2 | |||||||
DZW90 | 900 | 1350 | ≤450 | 60 | 24 | 2.2 | 128 | |
DZW90I | 48 | 36 | 3.0 | |||||
DZW120 | 1200 | 1800 | ≤600 | 60 | 24 | 3.0 | 132 | |
DZW120I | 48 | |||||||
DZW180 | 2500 | 3000 | ≤1250 |
70 |
25:1 | 24 | 4.0 | 245 |
36 | 5.5 | |||||||
DZW250 | 2500 | 3000 | ≤1250 | 24 | 5.5 | 250 | ||
DZW350 | 3500 | 4200 | ≤1750 | 75 | 13:1 | 18 | 7.5 | 450 |
DZW500 | 5000 | 6000 | ≤2500 | 10 | 460 |
Two: Technical Conditions
Z: Integrated Type T: Adjustable Type N: Smart Type
Protection Type: W for Outdoor, B for Explosion-Proof
Output Speed: Numerical, unit r/min (revolutions per minute)
Connection Type: T for Thrust Type, I for Power Station Type, Standard Type without Code; Rated Torque: Number indicates, unit kgf.m
Product Form: Multi-revolution electric device
1: Power: Motor is 3-phase AC 380V, 50Hz. Control is 2-phase AC 220V, 50Hz.
Optional Power Supply: AC 220~660V, 50/60Hz (to be specified at time of order) 2: Environmental Temperature; -20℃ to +60℃; Optional Temperature: -40℃ to +70℃
3: Relative humidity; not more than 95% (at 25°C)
4: Working Environment; Standard type for places without flammable, explosive, and highly corrosive media; Explosion-proof type (ExdIIBT4) suitable for II A, IIB groups T1-T4 explosive gases.
5: Protection Grade; IP65/67 (Special Order IP68)
Motor is in operation mode; rated running time 10 minutes. Class F insulation.
7: Corrosion-Resistant Coating: High-Temperature Painting
Product Featuresfeatures
Three: Adjust
Adjusting torque, during travel, ensure the potentiometer on the position indicator is disengaged (loosen the set screw on the gear of the potentiometer shaft) to prevent damage.
Torque control mechanism adjustment:
Firstly, adjust the torque.
(2) Begin with a low torque value and gradually increase it until the valve is completely closed.
(3) Adjust the torque for switch direction based on the valve's operational characteristics; typically, the open direction torque is greater than the close direction torque.
(4) Adjustments above are made under conditions of no load, no medium pressure, etc. When there is pressure and temperature, attention should be paid to whether it can be tightly sealed. If it cannot be sealed tightly, the torque value should be appropriately increased to ensure it can be tightly sealed and easily opened.
2. Travel control mechanism adjustment:
(1) Close the valve manually.
(2) Disengage the stroke control mechanism by using a screwdriver to push the top rod in the stroke control mechanism and rotate it 90°, thereby separating the driving pinion from the single-digit gear assembly of the counter.
(3) Rotate the "Off" adjustment shaft with a screwdriver in the direction of the arrow until the cam presses down on the spring plate, causing the microswitch to activate. This indicates that the "Off" travel has been initially adjusted.
（4）
At this point, turn the electric switch a few rotations and then turn it off. Check if the closing stroke meets the requirements; if not, adjust according to the aforementioned procedure.
(5) Direction Adjustment: After the valve is adjusted in the closed direction, manually open the valve to the desired position. Then disengage the stroke control mechanism, rotate the "open" adjustment shaft in the direction of the arrow until the cam presses against the spring plate, causing the microswitch to activate. Reengage the stroke mechanism with the driving gear, and the opening stroke is complete. After adjusting the stroke control mechanism, repeat the operation a few times. Generally, the valve is opened to about 90%.
3. Adjustment of the adjustable opening indicator:
Adjust the adjustable opening indicator and remote potentiometer after adjusting the torque and stroke.
Product detail imagesdetails
Suyu Brand Electric Device
Acid and alkali-resistant electric equipment
DZW60 Electric Unit
Corporate Strengthenterprise
Yangzhou Su Valve Control Equipment Co., Ltd. is located in the historic and cultural city of Yangzhou, China, and is a professional manufacturer specializing in the research, development, and market sales of valve electric actuators. The company has established a reliable quality assurance system, ensuring that the quality standards of its products are strictly implemented. The company's product range of valve electric actuators is comprehensive, widely used in engineering projects across various industries such as power, metallurgy, petroleum, chemicals, papermaking, and water supply and drainage, and has received high praise from customers. For many years, Yangzhou Su Valve Control Equipment Co., Ltd. has adhered to the business philosophy of "Quality, Integrity, and Customer First," gaining recognition from users across different industries, building the company's brand image, and creating high-quality products in the electric valve industry. The company's products are based in China and reach out to the world, serving more than 30 provinces, municipalities, and autonomous regions across the country. The company offers comprehensive customer service...
After-Sales Policyafter sale
Regarding shipment
Subject to customer's requirements.
About Returns and Exchanges
If any disputes arise upon receiving the product, please contact us promptly to negotiate a resolution.
Subject to customer's requirements
