Supply Electric Stop Valve J941H-16C DN125 Electric High-Temperature Steam Stop Valve Manufacturer Direct Supply
Product Features
Product advantage
Performance Parameters Table:
Parameter Name Model | Nominal Torque N.m | Torque Control N.m | Torque Control N.m | Allow passage through valve rod diameter | Manual Gear Ratio | Output Speed: rpm | Motor Power: kW | Weight: Kg |
DZW5 | 50 | 75 | ≤25 |
28 |
1:1 |
18 | 0.12 | |
DZW10 | 100 | 150 | ≤50 | 0.18 | ||||
DZW15 | 150 | 225 | ≤75 | 0.25 | ||||
DZW20 | 200 | 300 | ≤100 | 40 | 0.37 | |||
DZW20I | 28 | |||||||
DZW30 | 300 | 450 | ≤150 | 40 | 0.55 | |||
DZW30I | 28 | |||||||
DZW45 | 450 | 675 | ≤225 |
48 | 24 | 1.1 | 100 | |
36 | 1.5 | |||||||
DZW60 | 600 | 900 | ≤300 | 24 | 1.5 | 103 | ||
36 | 2.2 | |||||||
DZW90 | 900 | 1350 | ≤450 | 60 | 24 | 2.2 | 128 | |
DZW90I | 48 | 36 | 3.0 | |||||
DZW120 | 1200 | 1800 | ≤600 | 60 | 24 | 3.0 | 132 | |
DZW120I | 48 | |||||||
DZW180 | 2500 | 3000 | ≤1250 |
70 |
25:1 | 24 | 4.0 | 245 |
36 | 5.5 | |||||||
DZW250 | 2500 | 3000 | ≤1250 | 24 | 5.5 | 250 | ||
DZW350 | 3500 | 4200 | ≤1750 | 75 | 13:1 | 18 | 7.5 | 450 |
DZW500 | 5000 | 6000 | ≤2500 | 10 | 460 |
Two: Technical Conditions
Z: Integrated Type T: Adjustable Type N: Smart Type
Protection Type: W for Outdoor, B for Explosion-Proof
Output Speed: Numerical representation, unit r/min (revolutions per minute)
Connection Type: T for Thrust Type, I for Power Station Type, Standard Type without symbol; Rated Torque: Numbers indicate, unit in kgf.m
Product Form: Multi-rotary Electric Unit
Power: Motor is 3-phase AC 380V, 50Hz. Control is 2-phase AC 220V, 50Hz.
Optional Power Supply: AC 220~660V, 50/60Hz (to be specified at time of order) 2: Environmental Temperature; -20℃ to +60℃; Optional Temperature -40℃ to +70℃
3: Relative humidity; not greater than 95% (at 25°C)
4: Working Environment; Standard type for areas without flammable, explosive, and highly corrosive media; Explosion-proof type (ExdIIBT4) for use in IIA, IIB groups T1-T4 explosive gases.
5: Protection Grade; IP65/67 (Special Order IP68)
The motor operates in a duty cycle; rated running time is 10 minutes. F-grade insulation.
7: Corrosion-Resistant Coating: High-Temperature Bake Paint
Product Featuresfeatures
Three: Adjust
Adjust the torque, while in motion, ensure the potentiometer on the position indicator is disengaged (loosen the set screw on the gear of the potentiometer shaft to disengage) to prevent damage.
Torque control mechanism adjustment:
Firstly, adjust the torque.
(2) Begin with a low torque value and gradually increase it until the valve is fully closed.
(3) Adjust the torque for switching direction based on the valve's operational characteristics; typically, the torque for the open direction is greater than that for the close direction.
(4) Adjustments are made under conditions of no load, no medium pressure, etc. When there is pressure and temperature, attention should be given to whether it can be tightly sealed. If it cannot be sealed tightly, the torque value should be appropriately increased to ensure it can be tightly sealed and easily opened.
2. Traveler Control Mechanism Adjustment
(1) Manually close the valve tightly.
(2) Disengage the stroke control mechanism by using a screwdriver to push the top rod in the stroke control mechanism and rotate it 90°, thereby separating the driving small gear from the counter's unit gear set.
(3) Rotate the "OFF" position screwdriver towards the adjustment shaft, turning it in the direction of the arrow until the cam presses against the spring plate, causing the microswitch to activate. This indicates that the "OFF" travel has been initially adjusted.
（4）
At this point, you can electrically turn it a few rotations, then shut it off. Check if the closing travel meets the requirements. If not, adjust it again following the aforementioned procedure.
(5) Adjustment of Open Direction: After adjusting the closed direction, manually open the valve to the desired position. Then disengage the stroke control mechanism, rotate the "open" adjustment shaft in the direction of the arrow until the cam presses against the spring plate, causing the microswitch to actuate. Afterward, reengage the stroke mechanism with the driving gear, indicating the completion of the open direction stroke adjustment. Once the stroke control mechanism is adjusted, it can be operated repeatedly. Generally, the open valve is controlled around 90%.
Adjustment of the adjustable opening indicator:
Adjust the adjustable opening indicator and remote potentiometer after adjusting the torque and stroke.
Product detail imagesdetails
Soo Valve brand electric device
Acid and alkali-resistant electric device
DZW60 Electric Unit
Corporate Strengthenterprise
Yangzhou Suval Control Equipment Co., Ltd. is located in Yangzhou, a historic and cultural city in our country, and is a professional manufacturer specializing in the research, development, and market sales of valve electric actuators. The company has established a reliable quality assurance system, with product quality standards strictly implemented. Our product range of valve electric actuators is comprehensive and widely used in power, metallurgy, petrochemical, papermaking, water supply and drainage industries, and has received high praise from customers. For many years, Yangzhou Suval Control Equipment Co., Ltd. has adhered to the business philosophy of "Quality, Integrity, and Customer First," gaining recognition from users in various industries, building the company's brand image, and creating high-quality products in the electric valve industry. Our products are based in China and face the world, serving more than thirty provinces, municipalities, and autonomous regions across the country. The company offers comprehensive customer service...
After-Sales Policyafter sale
Regarding shipment
Subject to customer's requirements
About Returns and Exchanges
If there are any disputes upon receiving the product, please contact us promptly for negotiation and resolution.
Subject to customer's requirements
