Time-efficient oven drier

Heating Power:

27KW

Temperature Uniformity:

±4℃

Blower Power:

2 units, 1100W/380V

Common temperature required by the buyer:

Room Temperature-300℃

Specification Dimensions:

Studio Size:

1.4m x 1.3m x 1.2m (Workshop Material 304 Stainless Steel) Sizes Available for Customization

DeepWidth x Height

Approximate dimensions:

2.2m x 2.6m x 2.8m (including protrusions)

DeepWidth x Height

Interior cabinet material: heat-resistant steel, load-bearing1500KG

Overall Structure Overview:

Dual-side air outlet, top return air circulation, heating elements installed within the side air ducts of the cabinet, circulation motor installed within the top air duct of the oven, extending the motor's lifespan, double-door The door latch is secured with a goat horn rod.

Outer Box Material:

1.2mmCold-rolled carbon steel with a thickness of millimeters.Sheet metal bending, welding, and rivet assembly

Box housing vent panel material:

1.2mm thicknessCold-rolled carbon steelManufacture

Box duct material:

1.0mm thicknessCold-rolled carbon steel

Material for cabinet frame:

10# Channel Steel

Box Enhancement Material:

5# angle steel, locally bent from 2.0mm steel plate

Material for bottom load-bearing frame of the box:

12# Angle Steel

Material of the bottom of the case:

Two embedded grooves10# channel reinforcement, 12# track steel extended box outside, for easy sliding of small wheelies on top.

Top box frame material:

10# Channel Steel

Insulation thickness and material:

100KHigh-density ceramic fiber fillingInsulation thickness is:100mm）

Outer Carton Coating Material

After rust prevention treatment, surfaceEnvironmentally friendly self-drying paint, color: blue+Computer Grey

Door manufacturing method:

Exterior Wall Material:

1.2mm thicknessCold-rolled carbon steelManufacturing Sheet metal bending, welding, riveting and jointing

Interior door material:

1.2mm thicknessCold-rolled carbon steelManufacture Sheet metal bending, welding, and rivet assembly

Door Quantity:

Double doors

Door thickness:

120mm

Door Knob:

Alloy hinge and horn rod fixation, with top and bottom installation clips for excellent sealing.

Door Frame Sealing Material:

High-temperature asbestos rope seal

Door Opening Method:

Open from center to both sides

Studio Equipment:

Car Size:

Wide2.5 ft x 4.3 ft

Small Car Materials:

Adopt10# channel fabrication, covered with a 1.2mm steel plate on the surface, the trolley top equipped with horizontal steel bars for increased height, facilitating air intake, with handrails

Exhaust Valve

Exhaust:

1 piece

Blower System:

Blower type:

High-pressure circulating air flow

Motor Assembly:

Oven Top 2 units of 1100W

Wind Turbine Material:

Alloy Wind Turbine2

Heating System:

Heating Element:

Covered-sleeve far infrared heater(SHEATHED HEATER)U-shaped tubular electric heating generator, heating tube material: stainless steel.Resistant to slight acid and alkali corrosion; strong oil film adhesion after quenching.

Quantity of heating elements:

6 pieces

Heating Element Assembly

Side air ducts

Rise Time:

Can be manually set or programmed for temperature increase or decrease. Generally every minute3—7 degrees Celsius

Electrical specifications:

1Control Method: YuDi Instruments516P30 programmable temperature control, fuzzy PID adjustment, silicon-controlled rectifier output, noiseless, long lifespan

2PIDParameter auto-tuning function, manual/Automatic, interference-free switching function

3 Over-temperature alarm and forced power-off function

4 Programmable30Each section (process step) can set the temperature and time, and the process curve runs automatically according to the preset time.

5 Precision Temperature Control: Programmable with preset heating time and holding temperature.Insulation duration.After entering the insulation state, temperature fluctuations are minimal, generally.±1℃

6The heating power can automatically adjust according to the set temperature rise, highlighting the energy-saving effect.

7Control Features: Modular structure of control system, long-life design of critical equipment components, simple and reliable process, good stability, and high precision.