Duwan Environmental NS-4Submersible Pump MonitoringControllers are installed on the panel and can operate normally under the following conditions:
The surrounding environmental temperature does not exceed+40Please provide the Chinese content that needs to be translated.,24Average temperature within the hour does not exceed+35DegreeNo Chinese content provided for translation.Low environmental temperatures must not fall below-10No Chinese content provided.
No excessive dust, acids, salts, corrosive gases, or relative humidity abovePlease provide the Chinese content to be translated.No Chinese content provided.+40No Chinese content provided.50%During temperature reduction, higher relative humidity is permitted.
For example:20Temperature below degrees, humidity is90%Be cautious of condensation that may occur accidentally due to temperature changes.
Installation location's altitude does not exceed1000Mi.
Vertical installation tilt must not exceed5No Chinese content provided.
During the operation of the submersible pump,In cases where water leakage occurs in the pump oil chamber due to mechanical seal wear and other reasons,Controller via the pumpP31# P32#Signal lines are monitoring it., WhenP31#Please provide the Chinese content that needs to be translated into American English.P32#Our system has detected that water leakage has exceeded the threshold.,Control unit oil chamber leakage protection relay activated; oil chamber leakageLEDLight indicator (red) flashing. Oil chamber leakage relay.*Large Capacity2A 250VACAction state closed.
2.2 Protective Overtemperature for Pump Motor Windings
During the operation of the submersible pump,In the event of an overheating fault in the pump motor winding due to overloading or other reasons (with the action temperature value being...)135Please provide the Chinese content to be translated.,Controller through the pumpP11#P12#Or21#22#Signal lines monitor it.,Please provide the Chinese content that needs to be translated into American English.P11#Please provide the Chinese content to be translated.P12#Intermediate monitoring has detected temperatures exceeding135Due Time,Relay activated due to excessive temperature in the controller's winding, winding overheatingLEDLED (red) blinking. Winding overheating relay.Please provide the Chinese content to be translated.No Chinese content provided.2A 250VACAction status closed.
2.3 Water Pump Motor Cavity Submersion Protection
Due to seal wear and other reasons for the submersible pump,Pump motor chamber encounters water immersion failure,Controller through the pumpP51# P32#Signal lines monitor it.,WhenP51#Please provide the Chinese content you would like translated into American English.P32#Monitoring has detected water leakage exceeding normal levels.,Controller motor fault, protective relay activated; motor submerged in water.LEDLED (red) blinking. Fault relay.*No Chinese content provided.1A 250VACAction Groups Output Independently (Normally Open, Normally Closed).
2.4 Water Pump Terminal Box Compartment Waterproof Protection
When the submersible pump fails due to reasons such as seal wear,Cavity of the pump junction box encounters water immersion failure,Controller through the pumpP41# P32#Signal lines are monitoring it.,WhenP41#Please provide the Chinese content you would like translated.P32#We have detected that the water leakage exceeds the threshold.,Control panel junction box cavity submersion protection relay activated; junction box submergedLEDIndicator (red) blinking. Line box submersible relay*Large Capacity2A 250VACAction status closed.
2.5 Overheating Protection for Pump Bearings
When the pump bearing overheats due to overload or other reasons (with the operating temperature value of...),105No Chinese content provided.,Controller through the pumpP61# P32#Signal lines monitor it.,WhenP61#Please provide the Chinese content that needs to be translated into American English.P32#Intermediate monitoring has detected temperatures exceeding105Du Shi,Control unit motor fault, protective relay activated; bearing overheating.LEDThe indicator light (red) is blinking. Fault relay.*Large capacity1A 250VACTwo independent outputs (normally open, normally closed).
Warranty: One year. Free repair or replacement by the seller for any issues within one year!
Duwan Environmental NS-4 Comprehensive Protection and Monitoring ControllerPerformance Features
Input Voltage: AC220V, 50Hz, rated power consumption less than 10W.
Ambient Temperature: -20℃～75℃。
Ambient Humidity: Less than 90% (no dew condensation).
SensorPower Supply: SensorsDC 12V Low-Voltage Power Supply
Power Supply TransformerIsolation.
Signal Input: Input Offset Control:±2％；
Signal Input:DC12V switch quantity signal input or resistance, current signal input
Signal Response Speed:10mS。
Signal Output:RelayOutput, Touchpoint Capacity:5A/250VAC or 5A/30VDC.
1） NS-4Integrated Monitoring ControllerType
Signal Input: Winding Sensors: Winding Overheating Protection
Leakage Sensors: Oil Chamber Water Immersion Protection
Terminal BoxSensor: Cable Box Water-Proof Protection
Overload Signal: Overload Protection
MotorWaterproof Protection for Motors:腔传感
Pump Operation Signal: Pump Monitoring
Moisture Sensor: Dehumidification HeatingInsulating motors with a moisture removal and heating function.
Jiangsu Du'an Environmental ProtectionNS-4 Integrated Submersible Pump Monitoring ControllerCraftsmanship excellenceThe communication management chip, which is connected to the microcontroller, communicates with the computer terminal and transmits the transformer's temperature information to the computer terminal. Preferably, a buzzer is also connected to the microcontroller, which is in turn connected to the circuit with the temperature probe. When the temperature probe makes poor contact, the buzzer emits an alarm. Preferably, the display unit includes a digital tube, a digital tube driver circuit unit, and a key input control unit, as well as a key signal input editing unit. The digital tube is connected to the digital tube driver circuit unit and the key input control unit. The key signal input editing unit is connected to the digital tube driver circuit unit and the key input control unit, which are also connected to the microcontroller.
